manualshive.com logo in svg

Canon imagePASS-P1, Service Manual, Page: 4 / 70

Share
Download
Canon imagePASS-P1 Service Manual Download Page 4

Contents

1. Introduction...................................................................................................... 1

Introduction..........................................................................................................................................2

About the imagePASS...........................................................................................................................2
About this document..............................................................................................................................2
Document conventions.......................................................................................................................... 3
How the imagePASS operates...............................................................................................................3
Preparing for hardware installation or parts replacement..........................................................................3
Precautions.......................................................................................................................................... 3
Tools you will need................................................................................................................................5

2. Using the imagePASS......................................................................................6

Using the imagePASS.........................................................................................................................7

Starting, shutting down, rebooting, and restarting the imagePASS............................................................7

3. REPLACING PARTS.........................................................................................9

Replacing Parts.................................................................................................................................10

Replacing Parts...................................................................................................................................10
Accessing the imagePASS.................................................................................................................. 13
Checking imagePASS internal connections...........................................................................................14
Removing and replacing imagePASS components................................................................................ 15

Restoring imagePASS functionality after service.............................................................................. 34

4. INSTALLING SYSTEM SOFTWARE.............................................................. 35

Installing System Software................................................................................................................36

System software installation reminders................................................................................................. 36
Backing up and restoring the system configuration................................................................................ 36
Installing system software using a USB flash drive................................................................................ 38
Fiery Clone Tool..................................................................................................................................41
Printing the Configuration pages.......................................................................................................... 41

5. TROUBLESHOOTING.....................................................................................42

Troubleshooting.................................................................................................................................43

Symptoms and solutions......................................................................................................................44

6. SPECIFICATIONS........................................................................................... 51

Specifications.................................................................................................................................... 52

7. INSTALLATION PROCEDURE.......................................................................53

How to Check the Installation Procedure.......................................................................................... 54

Symbols............................................................................................................................................. 54

Check Items before Installation.........................................................................................................55

The IP addresses for communication between the host machine and equipment are set automatically..... 55

Contents

i

Summary of Contents for imagePASS-P1







































































Reviews:

No comments