manualshive.com logo in svg

Canon imagePASS-P1, Service Manual, Page: 39 / 70

Share
Download
Canon imagePASS-P1 Service Manual Download Page 39

Restoring imagePASS functionality after service

Complete your inspection and service by reinstalling and verifying the imagePASS.

To reinstall and verify the imagePASS

1. Reseat all boards, cables, connectors, and other parts loosened or removed during service.

When routing cables in the imagePASS make sure that:

• Covers are securely installed after routing cables.
• Cables are not looped around circuit boards or components (such as capacitors and resistors).
• Cable routing does not interfere with the operation of internal components.
• Cables do not lie on or against any internal heating element.
• Cables do not interfere with removing or replacing components.
• Cables do not interfere with opening or closing imagePASS panels.
• Cables are not tangled.
• Cable slack is secured with a tie-wrap.

IMPORTANT:

Improper connection of the internal power cables can damage the imagePASS. See 

“Checking imagePASS internal

connections” on page 14

.

2. Replace the cover on the imagePASS.

Make sure that all cables are fully inside the chassis before you replace the cover. Slide the cover until it engages the edge
of the chassis opposite the connector panel, and then lower the cover.

Figure 27: Replacing the chassis cover

3. Replace the two screws that you removed earlier.

Tighten the screws to secure the cover to the imagePASS.

4. Reinstall the imagePASS on the side of the printer.

For detailed information about removing/installing the printer, see the installation instructions that accompany the printer (not
included in this service guide).

5. Connect the external cables that you removed during inspection or service.

Be sure to properly connect the following cables (see 

“Checking imagePASS internal connections” on page 14

).

• Network cable
• Crossover Ethernet cable between the imagePASS and printer
• Printer interface cable
• imagePASS power cable

6. If you installed a new HDD, install system software (see

“Installing System Software” on page 36

).

A spare HDD is shipped without preinstalled system software.

7. Make sure to configure the date and time in Setup (see Configuration and Setup, which is part of the user documentation

set).

8. Before you leave the customer site, verify the imagePASS operation.

• Connect the imagePASS to the network (see

“Replacing Parts” on page 10

)

• Ask the site administrator to check the Setup options (see Configuration and Setup).

3. REPLACING PARTS

34

Summary of Contents for imagePASS-P1







































































Reviews:

No comments