Canon CR-X300 User Manual Download Page 92

Page: 92 / 114

C222 Recall preset during the color bars
output [warning]

C231 Trace execution during the washer
operation [warning]

C232 Trace execution during the color bars
output [warning]



RTP Warning

R101 RT

P authentication failure [notice]

R102 RT

P connection failure [notice]

R103 RTP session disconnected [notice]

R104 RTP session deleted [notice]

Notification Log



System Notification

001

ystem started [info]

002

ystem settings changed [info]

050 IPv4 address assigned to wired LAN

interface [info]

Description

Can't run preset, because color bars is
on. (C222)

Meaning

Preset was recalled during the color
bars output.

Countermeasure

Turn off the color bars output and recall
the preset again.

Description

Can't run trace, because washer is on.
(C231)

Meaning

Tracing was executed during the
washer operation.

Countermeasure

Wait until the washer operation stops,
then try executing trace again.

Description

Can't run trace, because color bars is
on. (C232)

Meaning

Tracing was executed during the color
bars output.

Countermeasure

Turn off color bars output and try tracing
again.

Description

RTSP Error: error_code=401:
Unauthorized (R101)

Meaning

RTSP authentication failed.

Description

RTSP Error: error_code=%d: (R102)

400: When an invalid RTSP request is
received etc.
503: The maximum number of RTP
connections has been exceeded, or a
request for multiple session streaming
with tunneling for the same stream has
been received, etc.

Meaning

RTSP connection has failed.

Description

session closed: num_of_sessions=%1
(R103)

Total number of sessions for clients

Meaning

The session was disconnected from the
client due to a factor other than
TEARDOWN. (For example, TCP FIN)

Description

session removed: num_of_sessions=%1
(R104)

Total number of sessions for clients

Meaning

The session was deleted due to errors.
(Session Timeout or when an invalid
RTSP request is received)

Description

starting paramd (S001)

Meaning

Parameter management module
started.

Description

Updated system settings. (S002)

Meaning

Settings which do not require rebooting
were changed.

Description

IPv4 Address %1 %2 was assigned to
the wired I/F (S050)

Set IPv4 address

from router for DHCPv4 address

Meaning

IPv4 address is set for wired LAN.

Summary of Contents for CR-X300



















































































































Search results

Summary of Contents for CR-X300

Reviews:

Related manuals for CR-X300

Brands by name

Popular brands

Canon CR-X300, User Manual

Search results

Summary of Contents for CR-X300

Reviews:

Related manuals for CR-X300

Brands by name

Popular brands