California Instruments 12000L-1P Instruction Manual Download

Page: 14 / 151

INSTRUCTIONAL MANUAL

2750L-P/4500L-P/6000L-P

August, 2001

Rev. K

-10-

phase of this input. Loss of this input will cause the output to default.

Indicators:

32 character LCD display, Output Overload, Over temperature Power On, High
Voltage Range.

Dimensions:

10.5 inches (26.7 cm) high, 23 inches (58.4 cm) deep and 19 inches (48.3 cm) wide.

Weight lbs (Kg):

175 (79.2)

Material:

Aluminum for Front panel, rear panel and top cover.

Steel for chassis.

Finish:

Front panel - painted gray 26440 per Federal Standard 595

Chassis - zinc plate type 2 class 2.

Rear panel and top cover - iridite.

Air intake/exhaust:

Intake from both sides of chassis.

Exhaust to the rear.

Modularity:

Oscillator, All amplifiers, DC power supplies, Current

Limit Board Assembly, Range-Relay Board, All displays

Connectors

Input Power:

Kulka terminal block, 9-85-5 (TB3)

Output Power:

Kulka terminal block, 9-85-4 (TB1)

Auxiliary Output Power: Barrier Strip (TB2)

External Sense:

AMP connector, 1-480705-0 (J6)

System

Interface

(mating connector):

3M Connector 3366-1001 plug

System Interface:

3M connector, 3367-1000 (J7)

IEEE-488 connector: J5

Chassis slides:

Zero Manufacturing Company Model CTN-1-20-E94

Operating temperature:

C to 50

Storage temperature:

-40

C to +85

Operating altitude:

0 to 6000 Ft.

Summary of Contents for 12000L-1P























































































































































Search results

Summary of Contents for 12000L-1P

Reviews:

Related manuals for 12000L-1P

Brands by name

Popular brands

California Instruments 12000L-1P, Instruction Manual

Search results

Summary of Contents for 12000L-1P

Reviews:

Related manuals for 12000L-1P

Brands by name

Popular brands