BTR DG-Mini Page 35 Manual Download

Page: 35 / 71

BTR Controls, Inc.

PROGRAMMING

DG-Mini V7 Rev. C Standard HW manual V 1.0.2

YSTEM

ONFIG

Description:

Fix picture

Timers

A submenu for configuring timers.

Outputs

A submenu for configuring outputs

Inputs

A submenu for configuring inputs

Position Sensor

A submenu for configuring the position sensor

Safety Edges

A submenu for configuring the wired safety edge

Mon Photo Eyes

A submenu for configuring monitored photoeyes

Motor Config

A submenu for configuring motor related settings

Frequencies

A submenu for configuring motor frequencies

Ramps

A submenu for configuring motor frequency ramps.

DG-Xnet

A submenu for configuring the DG-Xnet wireless options

Options

A submenu for configuring optional devices.

System

A submenu for configuring system level items.

Summary of Contents for DG-Mini








































































Search results

Summary of Contents for DG-Mini

Reviews:

Related manuals for DG-Mini

Brands by name

Popular brands

BTR DG-Mini, Manual

Search results

Summary of Contents for DG-Mini

Reviews:

Related manuals for DG-Mini

Brands by name

Popular brands