BTR DG-Mini Page 29 Manual Download

Page: 29 / 71

BTR Controls, Inc.

PROGRAMMING

DG-Mini V7 Rev. C Standard HW manual V 1.0.2

Express Menu

The Express menu provides a quick method to edit commonly used parameters.
It is entered by pressing

button while the controller is in the IDLE screen. It navigated using the standard

DOWN

and

MENU/ENTER

buttons described earlier.

XPRESS

ENU

Menu and Submenu

Description:

Display
Readout

Normal

Displays the standard Idle screen.

Motor Current

Displays actual motor current measured by the controller.

DC Link

Displays the internal DC Link voltage.

Position

Displays the current position in Encoder Counts.

Measured
Frequency

Displays the measured frequency calculated from a
compatible encoder.

Output Frequency

Displays the frequency output to the motor.

Auto 1 Timer

Shortcut to adjust the Auto 1 Timer.

Man 1 Timer

Shortcut to adjust the Manual 1 Timer.

DTO Timer

Shortcut to adjust the Delay To Open Timer.

DTC Timer

Shortcut to adjust the Delay To Close Timer.

Open Alarm

Shortcut to adjust the Open Alarm Timer.

Run Timer

Shortcut to adjust the Run Timer.

Emergency Jog

While in this menu the controller will operate jog mode.

WARNING

ANY CONNECTED SAFETY
INPUTS WILL BE IGNORED TO
ALLOW UNRESTRICTED
MOVEMENT OF THE DOOR.

Reset

Shortcut to reset the controller.

Summary of Contents for DG-Mini








































































Search results

Summary of Contents for DG-Mini

Reviews:

Related manuals for DG-Mini

Brands by name

Popular brands

BTR DG-Mini, Manual

Search results

Summary of Contents for DG-Mini

Reviews:

Related manuals for DG-Mini

Brands by name

Popular brands