BTG Visual-ICE User Manual Download Page 29

Page: 29 / 126

Visual-ICE™ Cryoablation System

2-7

2.9.2 Software Reset

The

Software Reset

button is used to boot the Visual-ICE Cryoablation System into a recovery mode

if the software becomes corrupted (reference Section 7.1).

2.9.3 Power Control Knob

The

Power Control Knob

powers ON the Visual-ICE Cryoablation System in preparation for a

procedure.

2.9.4 Needle Channels

The Needle Connection Panel contains ten numbered

needle

channels;

each channel contains two

ports to support connection of up to two cryoablation needles. Each channel operates independently

of all other channels in either freezing or thawing mode. The electrical connection is used for needles

with a memory chip, i-Thaw™, FastThaw™ or Cautery capabilities. The locking bar on each channel

locks the needles into the ports to secure them during the procedure.

Summary of Contents for Visual-ICE































































































































Search results

Summary of Contents for Visual-ICE

Reviews:

Related manuals for Visual-ICE

Brands by name

Popular brands

BTG Visual-ICE, User Manual

Search results

Summary of Contents for Visual-ICE

Reviews:

Related manuals for Visual-ICE

Brands by name

Popular brands