BTG Visual-ICE User Manual Download Page 112

Page: 112 / 126

7-30

User Manual

Message

Reason for Appearance

80-34 System Error

•

Fan X failure. At the conclusion of the procedure,

contact Galil Medical Customer Service.

•

Galil Medical Customer Service

o +1 877 639 2796 or
o +1 651 287 5000
o

[email protected]

Fan X was identified as not operating.

80-35 System Error

•

The gas flow rate in channel XX exceeds the

system operation requirements and may impact

performance. Reduce the number of active needles.

•

Galil Medical Customer Service

o +1 877 639 2796 or
o +1 651 287 5000
o

[email protected]

The calculated flow rate for a given

channel exceeded the optimum system

requirement. The number of active

needles should be reduced.

80-36 System Error

•

The gas flow rate exceeds the system operation

requirements and may impact performance. Reduce

the number of active needles

•

Galil Medical Customer Service

o +1 877 639 2796 or
o +1 651 287 5000
o

[email protected]

The cumulative flow rate for all channels

exceeded the optimum system

requirement. The number of active

needles should be reduced.

Summary of Contents for Visual-ICE































































































































Search results

Summary of Contents for Visual-ICE

Reviews:

Related manuals for Visual-ICE

Brands by name

Popular brands

BTG Visual-ICE, User Manual

Search results

Summary of Contents for Visual-ICE

Reviews:

Related manuals for Visual-ICE

Brands by name

Popular brands