manualshive.com logo in svg

BRP SEA-DOO GTI 130 2019, Operator'S Manual

Share
Download
BRP SEA-DOO GTI 130 2019 Operator'S Manual Download Page 139

STORAGE AND PRESEASON PREPARATION

219001838-023_a

TYPICAL

1. Flushing connector

The following hose can be fabricated to
ease draining procedure.

smo2008-001-053_a

TYPICAL

1. Flushing connector adapter
2. Hose 12.7 mm (1/2 in)
3. Air hose male adapter

NOTICE

Failure to drain the ex-

haust system may cause severe
damage to the intercooler (super-
charged models) and exhaust mani-
fold.

Remove special tools.

Engine Internal Lubrication

1. Open the seat.

2. Remove ignition coils,

refer to

MAINTENANCE PROCEDURES

.

3. Remove spark plugs, refer to

MAIN-

TENANCE PROCEDURES

.

4. Spray LUB. & ANTI-CORROSIVE

(P/N 779168) or equivalent in spark
plug holes.

5. To prevent fuel from being injected

and to disable the ignition during en-
gine cranking, fully depress throttle
lever and HOLD against handlebar.

6. Press the START/STOP button to

crank the engine a few turns. This
will distribute the oil on the cylinder
walls.

7. Apply anti-seize lubricant on spark

plug threads, then reinstall them
in the engine. Refer to

MAINTE-

NANCE PROCEDURES

.

8. Install the ignition coils, refer to

MAINTENANCE PROCEDURES

.

Engine Coolant Test

If antifreeze is not replaced, test its
density.

The antifreeze replacement and a den-
sity test should be performed by an au-
thorized Sea-Doo dealer.

NOTE:

Antifreeze should be replaced

every 300 hours or every 5 years to
prevent antifreeze deterioration.

NOTICE

Improper antifreeze den-

sity may result in freezing of the liq-
uid in the cooling system if the wa-
tercraft is stored in an area where
the freezing point is attained. This
could seriously damage the engine.

Electrical System

Battery Removal and Charging

Contact

your

authorized

Sea-Doo

dealer.

WARNING

Never charge or boost the battery
while installed in the watercraft.

Engine Compartment

Engine Compartment Cleaning

Clean the bilge using hot water and a
mild detergent or with bilge cleaner.

Rinse thoroughly.

Lift front end of watercraft to com-
pletely drain bilge through the bilge
drain plugs.

______________

137

https://www.boat-manuals.com/

Summary of Contents for SEA-DOO GTI 130 2019













































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands