manualshive.com logo in svg

BRP SEA-DOO GTI 130 2019, Operator'S Manual

Share
Download
BRP SEA-DOO GTI 130 2019 Operator'S Manual Download Page 114

OPERATING MODES

NOTE:

The SKI MODE indicator will

also come ON and blink when ski mode
becomes active. It will be ON steady
when the operator pulls and holds the
throttle lever all the way in to the han-
dlebar.

smo2011-003-100_o

SKI MODE INDICATOR

9. To launch the PWC in ski mode, pull

in and hold the throttle lever all the
way to the handlebar grip. The PWC
will accelerate to the set TARGET
SPEED and the SKI MODE indicator
will be on steady.

10. To increase or decrease the TAR-

GET SPEED during a ski run, press
the UP/DOWN button,

do not

re-

lease the throttle lever.

sdd2009-001-024_h

1. Hold throttle lever in
2. Press UP button to increase speed
3. Press DOWN button to decrease speed

NOTE:

If the throttle is partly released

during a ski run, the SKI MODE indica-
tor light will start to blink and the speed
adjust function using the UP/DOWN ar-
row button will be deactivated.

11. To end a ski run or to pick up a fallen

skier or wakeboarder, fully release
the throttle to regain normal throt-
tle control.

NOTE:

When the throttle is fully re-

leased during ski mode operation, the
system returns to ski mode engaged
status. The SKI MODE indicator light
will go out but, ski mode will remain
engaged and a message to that effect
will reappear in the multifunction dis-
play.

12. Press SET to reactivate ski mode

and fully pull in the throttle lever to
start another ski run.

Deactivating Ski Mode

To exit ski mode at any given point dur-
ing the ski mode setting process, press
the MODE button.

To end a ski run and completely deac-
tivate ski mode, release the throttle to
idle, then press the MODE button.

Learning Key Mode

Learning key provides a mode of opera-
tion whereby engine power and speed
is limited.

There are 5 speed settings available for
the learning key mode. By default, the
key modes are preset to the speed set-
ting (3).

NOTE:

Changing key settings is only

available when the engine is not run-
ning.

Changing Learning Key Speed
Settings

GTR-X Models

The default learning key setting is
51 km/h (32 MPH) .

Contact an authorized Sea-Doo dealer
for adjustment.

112

______________

https://www.boat-manuals.com/

Summary of Contents for SEA-DOO GTI 130 2019













































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands