BRP SEA-DOO GTI 130 2019 Operator'S Manual Download Page 133

Page: 133 / 204

MAINTENANCE PROCEDURES

219001838-023_a

TYPICAL

1. Flushing connector location

NOTE:

An optional quick connect hose

adapter and hose fitting can be used
(P/N 295 500 473) or equivalent. No
hose pincher is required to flush en-
gine.

219001838-026_a

TYPICAL - QUICK CONNECT HOSE ADAPTER

219001838-025_a

TYPICAL

1. Hose adapter (optional, not mandatory)
2. Quick connect fitting (optional, not

mandatory)

3. Garden hose

To flush, start engine then immediately
open the water tap.

CAUTION

Many components

in the engine compartment may be
very hot. Direct contact may result
in skin burn. Do not touch any elec-
trical parts or propulsion system
component when the engine is run-
ning.

NOTICE

Never flush a hot en-

gine. Always start the engine before
opening the water tap. Open wa-
ter tap immediately after engine is
started to prevent overheating.

Run the engine 90 seconds at idle
speed.

NOTICE

Never run engine without

supplying water to the exhaust sys-
tem when watercraft is out of water.

Ensure water flows out of jet pump
while flushing. Otherwise, refer to an
authorized Sea-Doo dealer for servic-
ing.

NOTICE

Never run engine longer

than 2 minutes. Drive line seal has
no cooling when watercraft is out of
water.

Close the water tap, run the engine at
5000 RPM for 5 seconds and stop the
engine.

NOTICE

Always close the water

tap before stopping the engine. If
not, water will get inside the engine.

NOTICE

Remove

quick connect

adapter after flushing operation (if
used).

Ride Plate and Water Intake
Grate

Ride Plate and Water Intake Grate
Inspection

Inspect ride plate and jet pump wa-
ter intake grate for damage. See your
Sea-Doo dealer to have any damaged
part repaired or replaced.

______________

131

https://www.boat-manuals.com/

Summary of Contents for SEA-DOO GTI 130 2019













































































































































































































Search results

Summary of Contents for SEA-DOO GTI 130 2019

Reviews:

Brands by name

Popular brands

BRP SEA-DOO GTI 130 2019, Operator'S Manual

Search results

Summary of Contents for SEA-DOO GTI 130 2019

Reviews:

Brands by name

Popular brands