background image

SPECIAL PROCEDURES

Clean the water intake area. If the sys-
tem is still clogged, refer to an autho-
rized Sea-Doo dealer for servicing.

NOTICE

Inspect water intake grate

for damage. Refer to an authorized
Sea-Doo dealer for repair as neces-
sary.

Watercrafts Equipped with iBR

For ease of access to the propulsion
system, move the iBR to the for-
ward position, refer to

iBR OVERRIDE

FUNCTION

for detailed instructions.

iBR Override Function (Models
Equipped with iBR)

When the iBR override function is acti-
vated, it allows the user to electrically
move the iBR gate and nozzle through
its full range of motion using the VTS
control button.

NOTE:

The iBR override function is

only available when the engine is not
running.

WARNING

When moving the iBR gate using
the iBR override function, ensure
no-one is near the rear of the wa-
tercraft. Movement of the gate
may squeeze fingers.

NOTICE

An object or tool caught

in the iBR system when using the
iBR override function may cause
damage to the iBR components. Re-
move all rigid foreign objects that
may obstruct the iBR gate travel be-
fore moving it.

WARNING

If it is necessary to reach in to re-
move any foreign object caught
in the propulsion system, strictly
observe the following before pro-
ceeding:

– Remove tether cord from the

engine cut-off switch.

– Wait at least 5 minutes.
– Do not press on START/STOP

button.

Should

the

START/

STOP button is pressed, wait
another 5 minutes.

Activating iBR Override Function

To activate the iBR override function,
carry out the following step.

1. Briefly press START/STOP button to

activate the electronic module.

2. Install the tether cord on the engine

cut-off switch (D.E.S.S. post).

3. Squeeze and hold the LH lever.

ssi2015-005-024_a

1. LH lever squeezed and held

4. When the

IBR OVERRIDE - PRESS

OK

message appears in the multi-

function gauge, press the SET or OK
button.

When the function is activated, a ON
message will be shown.

5. While still holding the LH lever,

press the UP/DOWN switch to po-
sition the iBR gate in the required
position.

116

______________

https://www.boat-manuals.com/

Summary of Contents for SEA-DOO GTI 130 2019













































































































































































































Reviews: