Brother 882-C40 Operational Manual Download Page 310 | Manualshive

Page: 310 / 332

background image

TROUBLESHOOTING

A-24

d

While holding the bobbin in place with
your finger, pass the thread through the slit
in the needle plate.

*

Hold down the bobbin with your right hand, and
then pull the end of the thread around the tab with
your left hand.

a

Tab

b

Hold down the bobbin with your right hand.

Pull the thread to pass it through the slit in the
needle plate, then cut it with the cutter.

c

Slit

d

Cutter

Sewing with the correct thread tension is possible
after the bobbin has been correctly installed in the
bobbin case.

Tangled thread on wrong side of
fabric

■

Symptom

*

The thread becomes tangled on the lower side of the
fabric.

*

After starting sewing, a rattling noise is made and
sewing cannot continue.

*

Looking under the fabric, there is tangled thread in
the bobbin case.

■

Cause

Incorrect upper threading

If the upper thread is incorrectly threaded, the upper
thread passed through the fabric cannot be firmly
pulled up and the upper thread becomes tangled in
the bobbin case, causing a rattling noise.

■

Remedy/check details

Remove the tangled thread, and then correct the
upper threading.

a

Remove the tangled thread. If it cannot be
removed, cut the thread with scissors.

*

Refer to “Cleaning the Race” in “CARE AND
MAINTENANCE” on page A-19.

b

Remove the upper thread from the
machine.

c

Refer to the following steps to correct the
upper threading.

*

If the bobbin was removed from the bobbin case,
refer to “LOWER THREADING” on page B-40 and
“Remedy/check details” in the section “Upper
thread tightened up” on page A-23 to correctly
install the bobbin.

«
...
308
309
310
311
312
...
»

Summary of Contents for 882-C40













































































































































































































































































































































Reviews:

No comments

Related manuals for 882-C40

Brand: Canon Pages: 100

Brand: Canon Pages: 124

Brand: Canon Pages: 203

Brand: Canon Pages: 28

MICRO-IMAGECHECKER A200 Series

Brand: Panasonic Pages: 102

Brand: ADJ Pages: 10

Brand: Windsor Pages: 25

Autopax PAX600H

Brand: Quasar Pages: 148

Brand: Altrad Belle Pages: 46

Brand: MasterCraft Pages: 8

Brand: JBI Pages: 36

Brand: JUKI Pages: 12

Brand: Brother Pages: 204

Brand: Global Pages: 2

Brand: JUKI Pages: 18

Brand: JUKI Pages: 32

Innov-is NV1800Q

Brand: Brother Pages: 32

Brand: Brother Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands