Brother 882-C40 Operational Manual Download Page 133

Page: 133 / 332

SEWING THE STITCHES

tility
S

titc
h

Sewing

S-45

Using the measurement on the quilting foot
as a guide, sew around the motif.

6.4 mm (approx. 1/4 inch)

Finished project

Press

to cancel the free motion sewing

mode.

→

Rotate the handwheel toward you
(counterclockwise) to raise the feed dogs.

Blind Hem Stitches

Secure the bottoms of skirts and pants with a blind
hem. Two stitches are available for blind hem
stitching.

Turn the skirt or pants wrong side out.

Wrong side of fabric

Right side of fabric

Edge of fabric

Bottom side

Fold the fabric along the desired edge of the
hem, and press.

Stitch

Stitch name

Presser foot

Blind hem stitch

Blind hem stitch stretch

Memo

• When the size of cylindrical pieces is too

small to slide onto the arm or the length is
too short, the fabric will not feed and
desired results may not be achieved.

Wrong side of fabric

Right side of Fabric

Edge of fabric

Desired edge of hem

<Seen

from the side>

Summary of Contents for 882-C40













































































































































































































































































































































Search results

Summary of Contents for 882-C40

Reviews:

Related manuals for 882-C40

Brands by name

Popular brands

Brother 882-C40, Operational Manual

Search results

Summary of Contents for 882-C40

Reviews:

Related manuals for 882-C40

Brands by name

Popular brands