4
PREPARATION
Factory packaging must be removed, and some minor assembly
work is required prior to installation. Access to the rear of the stove
is necessary. The circuit board/control panel must be unpacked
and installed in the side flashing on the insert or side panel on the
freestanding (see installation instructions provided with the circuit
board). NOTE: Normally, your dealer will perform these functions.
CLEARANCES
This freestanding unit has been tested and listed for installation in
residential, mobile home, and alcove applications. This insert unit is
approved for installation into code complying masonry fireplaces. It
is also approved for use in listed factory built fireplaces (UL 127) and
standard residential built-ins (see “As A Built-In Fireplace” section
of this manual), including Mobile Home built-in installations, of the
following description: all brands at least 34” (864 mm) wide and 20-
1/2” (521 mm) high.
FLOOR PROTECTION
SIDEWALL CLEARANCES
Adjacent Wall
Adjacent Wall
With
Vertical
Exhaust
Backwall
Sidewall
*
8 -1/4 “
210 mm
(top)
1 “
26 mm
1 “
26 mm
1 “
26 mm
3 “
77 mm
3 “
77 mm
3 “
77 mm
9 “
229 mm
(sidewall)
28”
712 mm
6” 153mm
2” (51 mm)
2” (51 mm)
ALCOVE CLEARANCES
36” (915 mm) max.
48”
(1220 mm)
min.
*
WITH HORIZONTAL EXHAUST
38” (966 mm) min.
Backwall
With
Vertical
Exhaust
Stove Door Face Must Be
Equal To Or Pritrude Out
From Face Of Alcove.
8 -1/4”
210 mm
(Top)
3”
77 mm
*1”
26 mm
9”
229 mm
(Sidewall)
9”
229 mm
(Sidewall)
8 -1/4”
210 mm
(Top)
COMBUSTIBLE
WALL
NON
COMBUSTIBLE HEA
RTH
HEA
RTH E
XTENSION
COMBUSTIBLE F
LOOR
SIDE
FACING
MANTLE
6”
(153 mm)
6”
(153 mm)
12”
(305 mm)
0
10”
(254 mm)
TOP
FACIN
G
12”
(305 mm)
12”
(305 mm)
Freestanding
Width
22-1/2” (572 mm)
Height
28-1/2” (724 mm)
Depth
24” (610 mm)
Weight
185 lbs (84 kg)
Pedestal
40 lbs (18 kg)
Legs
13 lbs (6kg)
Flue size
3” (77 mm) or 4” (102 mm)
Hopper Capacity
Up to 45 lbs. (20 kg) (This can vary widely
depending on pellet size, length, and
diameter)
Burn time
4-1/2 lbs (2 kg) per hour
Approved
Installations
Mobile Home, Alcove, Conventional
Fireplace Insert
Width
21-1/2” (547 mm) (with flashing: 39” (991
mm))
Height
20” (508 mm) (with flashing: 30” (762 mm))
Depth
24” (610 mm) (in fireplace: 10-3/4” (274 mm))
Weight
185 lbs. (84 kg)
Flashing
13 lbs. (6 kg)
Flue size
3” (77 mm) or 4” (102 mm)
Hopper Capacity
Up to 45 lbs. (20 kg) (this can vary widely
depending on pellet size, length, and
diameter)
EPA status
Exempt
Burn time
4-1/2 lbs. (2 kg) per hour
Approved
Installations
zero-clearance masonry, as a built-in.
INSTALLATION
