8
A. ASSEMBLING THE FLASHING SET
Follow the instructions packaged with the flashing set.
B. WHEN VENT PIPE EXTENDS TO CHIMNEY TOP
1. You will need a pipe length equal to the chimney height (from
hearth) plus 6” (153 mm). If outside combustion air is to be used,
you will need a pipe length (see “Combustion Air Supply” section
of this manual) equal to the chimney height plus 12” (305 mm).
2. Attach cerablanket wrap (not included) to that end of vent pipe
that will connect to the stove. Use 12” (305 mm) lengths of light
gauge metal wire (not included) or metallic tape (not included).
This is to protect interior components from excess heat.
3. Set the insert on the hearth and slide it in far enough to attach
the vent pipe (and combustion pipe if used).
4. Attach flashing, route power cord out the side nearest a 120V
receptacle. Slide the insert in.
5. Measure and build chimney top. Cut out hole for vent pipe (and
combustion air intake pipe, if used). Install and seal with a non-
hardening mastic to prevent water leakage. Install the vent cap.
C. WHEN VENT PIPE EXTENDS THROUGH CHIMNEY BLANKING
PLATE (Masonry Fireplaces Only).
1. You will need a pipe length that extends 12” (305 mm) above
the blanking plate. NOTE: This installation is optional but not
recommended. Outside combustion air cannot be drawn from
the chimney cavity in this installation.
2. Attach cerablanket wrap (not included) to that end of vent pipe
that will connect to the stove. Use 12” (305 mm) lengths of light
gauge metal wire (not included) or metallic tape. This is to
protect interior components from excessive heat.
3. Measure and build blanking plate. Cut out hole for vent pipe (and
combustion air intake pipe, if used). Install and carefully seal
blanking plate with non-hardening mastic. Failure to properly
seal may result in smoke spillage.
4. Slide vent pipe (and intake pipe if used) up through the blanking
plate hole, leaving enough to pull back down.
5. Set the insert on the hearth, adjust the leveling bolts on the
rear sides, slide it in far enough to attach the vent pipe (and
combustion air pipe if used). Be sure to seal where the pipe
passes through the blanking plate.
6. Attach flashing, route power cord out the side nearest a 120V
receptacle. Slide the insert in.
6” (153 mm)
6”
(153 mm)
max
15”
(381 mm)
3”
(77 mm)
TOP PLATE (SEAL TO
CHIMNEY TOP WITH
NON-HARDENING
MASTIC)
TOP PLATE (SEAL TO
CHIMNEY TOP WITH
NON-HARDENING
MASTIC)
NOTE:
FOLLOW METAL
CHIMNEY INSTALLATION
INSTRUCTIONS
BLANKING PLATE
(SEAL WITH NON-
HARDENING MASTIC)
LEVELING BOLTS
EXHAUST PIPE
INSTALLATION
HEARTH
NOTE:
FOLLOW METAL
CHIMNEY
INSTALLATION
INSTRUCTIONS
EXTENSION TO CHIMNEY
TOP OPTIONAL. (REQUIRED
IN MOBILE HOME AND
ZERO-CLEARANCE
FIREPLACES.
RECOMMENDED IN ALL
FIREPLACES).
3” OR 4” (77 mm or 102 mm)
STAINLESS STEEL SINGLE
WALL PIPE.
BLANKING PLATE (SEAL WITH
NON-HARDENING MASTIC).
CHIMNEY NEED ONLY EXTEND
12” (305 mm) ABOVE BLANKING
PLATE.
12”
(305 mm)
3” OR 4” (77 mm or 102 mm)
STAINLESS STEEL
FLEX PIPE.
FIREPLACE INSERT
SIDE ELEVATION
1” (26 mm) CERIBLANKET
NOTE:
WHEN MANTLE EXTENDS
MORE THAN 6” (153 mm)
FROM FIREPLACE FACE,
A 15” (381 mm) MINIMUM
DIMENSION MUST BE
MAINTAINED FROM
STOVE TOP TO BOTTOM
OF MANTLE.
OUTSIDE
COMBUSTION AIR
INSTALLATION
HEARTH
OPTIONAL COMBUSTION AIR
INTAKE (EXTENDS THROUGH
CHIMNEY TOP WITH180°
BEND) REQUIRED IN A
MOBILE HOME AND
ZERO-CLEARANCE
FIREPLACES.
NOT RECOMMENDED IN
MASONRY FIREPLACES OR
BUILT-IN INSTALLATIONS.
6” (153 mm)
6”
(153 mm)
max
15”
(381 mm)
3”
(77 mm)
TOP PLATE (SEAL TO
CHIMNEY TOP WITH
NON-HARDENING
MASTIC)
TOP PLATE (SEAL TO
CHIMNEY TOP WITH
NON-HARDENING
MASTIC)
NOTE:
FOLLOW METAL
CHIMNEY INSTALLATION
INSTRUCTIONS
BLANKING PLATE
(SEAL WITH NON-
HARDENING MASTIC)
LEVELING BOLTS
EXHAUST PIPE
INSTALLATION
HEARTH
NOTE:
FOLLOW METAL
CHIMNEY
INSTALLATION
INSTRUCTIONS
EXTENSION TO CHIMNEY
TOP OPTIONAL. (REQUIRED
IN MOBILE HOME AND
ZERO-CLEARANCE
FIREPLACES.
RECOMMENDED IN ALL
FIREPLACES).
3” OR 4” (77 mm or 102 mm)
STAINLESS STEEL SINGLE
WALL PIPE.
BLANKING PLATE (SEAL WITH
NON-HARDENING MASTIC).
CHIMNEY NEED ONLY EXTEND
12” (305 mm) ABOVE BLANKING
PLATE.
12”
(305 mm)
3” OR 4” (77 mm or 102 mm)
STAINLESS STEEL
FLEX PIPE.
FIREPLACE INSERT
SIDE ELEVATION
1” (26 mm) CERIBLANKET
NOTE:
WHEN MANTLE EXTENDS
MORE THAN 6” (153 mm)
FROM FIREPLACE FACE,
A 15” (381 mm) MINIMUM
DIMENSION MUST BE
MAINTAINED FROM
STOVE TOP TO BOTTOM
OF MANTLE.
OUTSIDE
COMBUSTION AIR
INSTALLATION
HEARTH
OPTIONAL COMBUSTION AIR
INTAKE (EXTENDS THROUGH
CHIMNEY TOP WITH180°
BEND) REQUIRED IN A
MOBILE HOME AND
ZERO-CLEARANCE
FIREPLACES.
NOT RECOMMENDED IN
MASONRY FIREPLACES OR
BUILT-IN INSTALLATIONS.
BRECKWELL ZC
ADJUSTABLE LEGS
FIGURE 14
FIGURE 15
(OPTIONAL)
BRASS
TRIM
(OPTIONAL)
BRASS
TRIM
(OPTIONAL)
BRASS
TRIM
TOP SURR
OUND P
ANEL
CIR
CUIT
BO
ARD
LEFT SIDE
SURR
OUND
PANEL
RIGHT SIDE
SURR
OUND
PANEL
LEVELING
BOL
T
