Bosch VJT-X20XF-E Installation And Operating Manual Download

Page: 19 / 124

VideoJet XF E

Installation | en

Bosch Sicherheitssysteme GmbH

Installation and Operating Manual

DOC | V5.51 | 2012.03

4.4

Connections

Camera

You can connect a maximum of two video sources to the VideoJet X20 XF E or a maximum of

four video sources to the VideoJet X40 XF E. Any cameras and other video sources that

produce a standard PAL or NTSC signal are suitable.

Connect the cameras or other video sources to the BNC

VIDEO IN

sockets using a video

cable (75 Ohm, BNC plug).

If the video signal is not looped through, termination is performed by a software setting if

necessary.

Further topics:

–

Section 5.19 Advanced Mode: Privacy Masks, page 42

Audio connection

The VideoJet XF E has two audio ports for audio line signals (stereo input and mono output).

The audio signals are transmitted two-way and in sync with the video signals. As a result, you

can connect a speaker or door intercom system at the destination point, for example. The

following specifications should be complied with in all cases.

The stereo plugs must be connected as follows:

Connect one or two audio sources with line level to the

AUDIO IN

socket of the

VideoJet XF E with a 3.5 mm stereo plug.

Connect a speaker to the

AUDIO OUT

socket of the VideoJet XF E with a 3.5 mm stereo

plug.

Network

You can connect the VideoJet XF E to a 10/100 Base-T network using a standard UTP

category 5 cable with RJ45 plugs.



Connect the VideoJet XF E to the network via the

ETH

socket.

CF slot

You can insert a standard Type I/II CompactFlash memory card into the

CF CARD

slot to

enable recordings to be saved locally. CF cards are the ideal solution for shorter storage times

and temporary recordings, for example alarm recordings or local buffering in the event of

network interruptions.

2 ×

AUDIO IN

Impedance 9 kOhm typ., 5.5 V

p-p

max. input voltage

1 ×

AUDIO OUT

3 V

p-p

typ. output voltage at 10 kOhm impedance,

2.3 V

p-p

typ. output voltage at 32 Ohm impedance,

1.7 V

p-p

typ. output voltage at 16 Ohm impedance

Contact

AUDIO IN function

AUDIO OUT function

Tip

Line In 1

Line Out 1

Middle ring

Line In 2

Line Out 1

Lower ring

Ground

NOTICE!

The release letter for the current firmware version includes a list of compatible CF cards.

Summary of Contents for VJT-X20XF-E





























































































































Search results

Summary of Contents for VJT-X20XF-E

Reviews:

Related manuals for VJT-X20XF-E

Brands by name

Popular brands

Bosch VJT-X20XF-E, Installation And Operating Manual

Search results

Summary of Contents for VJT-X20XF-E

Reviews:

Related manuals for VJT-X20XF-E

Brands by name

Popular brands