Bosch VJT-X20XF-E Installation And Operating Manual Download

Page: 108 / 124

108

en | Appendix

VideoJet XF E

DOC | V5.51 | 2012.03

Installation and Operating Manual

Bosch Sicherheitssysteme GmbH

8.3

Malfunctions with iSCSI connections

8.4

LEDs

The VideoJet XF E network video server has LEDs on its front and rear panels that show the

operating status and can give indications of possible malfunctions:

CONNECT LED

LINK LED

REC LED

8.5

Processor load

If the VideoJet XF E is accessed via the Web browser, you will see the processor load

indicator in the top left of the window next to the manufacturer's logo.

You can obtain additional information to help you when troubleshooting or fine tuning the

unit. The values indicate the proportions of the individual functions on the encoder load,

shown as percentages.

Web browser contains

empty fields.

Active proxy server in network.

Create a rule in the local

computer's proxy settings to

exclude local IP addresses.

The

CONNECT

LED

flashes red.

Firmware upload failed.

Repeat firmware upload.

Malfunction

Possible causes

Recommended solution

Malfunction

Possible causes

Recommended solution

After connecting to the

iSCSI target, no LUNs are

displayed.

Incorrect LUN mapping during

iSCSI system configuration.

Check the iSCSI system

configuration and reconnect.

After connecting to the

iSCSI target, "LUN FAIL"

appears below a node.

The LUN list could not be read,

as it was assigned to the wrong

network interface.

Check the iSCSI system

configuration and reconnect.

LUN mapping is not

possible.

Some iSCSI systems do not

support the use of an initiator

extension.

Delete the initiator extension on

the

Identification

configuration

page.

Does not light up:

VideoJet XF E is switched off.

Lights up green:

VideoJet XF E is switched on.

Lights up red:

Startup in progress.

Flashes green:

Data packet transmission via network.

Flashes red:

VideoJet XF E is faulty, for example following failed

firmware upload.

Lights up green:

Network connection established.

Flashes orange:

Recording in progress.

Summary of Contents for VJT-X20XF-E





























































































































Search results

Summary of Contents for VJT-X20XF-E

Reviews:

Related manuals for VJT-X20XF-E

Brands by name

Popular brands

Bosch VJT-X20XF-E, Installation And Operating Manual

Search results

Summary of Contents for VJT-X20XF-E

Reviews:

Related manuals for VJT-X20XF-E

Brands by name

Popular brands