Bosch VJT-X20XF-E Installation And Operating Manual Download

Page: 6 / 124

en | Preface

VideoJet XF E

DOC | V5.51 | 2012.03

Installation and Operating Manual

Bosch Sicherheitssysteme GmbH

Preface

1.1

About this manual

This manual is intended for persons responsible for the installation and operation of the

VideoJet XF E and applies to all variants. In the drawings the VideoJet X40XF E is displayed

standing for all versions. International, national and any regional electrical engineering

regulations must be followed at all times. Relevant knowledge of network technology is

required. The manual describes the installation and operation of the unit.

1.2

Conventions in this manual

In this manual, the following symbols and notations are used to draw attention to special

situations:

1.3

Intended use

The VideoJet XF E network video server transfers video, audio and control signals over data

networks (Ethernet LAN, Internet). There are various memory options for recording the

images captured by the connected cameras. The unit is intended for use with CCTV systems.

Various functions can be triggered automatically by incorporating external alarm sensors.

Other applications are not permitted.

In the event of questions concerning the use of the unit which are not answered in this

manual, please contact your sales partner or:

Bosch Sicherheitssysteme GmbH

Robert-Bosch-Ring 5

85630 Grasbrunn

Germany

www.boschsecurity.com

1.4

EU Directives

The VideoJet XF E network video server complies with the requirements of EU Directives 89/

336 (Electromagnetic Compatibility) and 73/23, amended by 93/68 (Low Voltage Directive).

1.5

Rating plate

For exact identification, the model name and serial number are inscribed on the bottom of the

housing. Please make a note of this information before installation, if necessary, so as to have

it to hand in case of questions or when ordering spare parts.

CAUTION!

This symbol indicates that failure to follow the safety instructions described may endanger

persons and cause damage to the unit or other equipment.

It is associated with immediate, direct hazards.

NOTICE!

This symbol refers to features and indicates tips and information for easier, more convenient

use of the unit.

Summary of Contents for VJT-X20XF-E





























































































































Search results

Summary of Contents for VJT-X20XF-E

Reviews:

Related manuals for VJT-X20XF-E

Brands by name

Popular brands

Bosch VJT-X20XF-E, Installation And Operating Manual

Search results

Summary of Contents for VJT-X20XF-E

Reviews:

Related manuals for VJT-X20XF-E

Brands by name

Popular brands