Bosch VJT-X20XF-E Installation And Operating Manual Download

Page: 109 / 124

VideoJet XF E

Appendix | en

109

Bosch Sicherheitssysteme GmbH

Installation and Operating Manual

DOC | V5.51 | 2012.03



Move the cursor over the graphic indicator. Some additional numerical values are also

displayed.

8.6

Network connection

You can display information about the network connection. To do this, move the cursor over

8.7

Serial interface

Options for using the serial interface include transferring transparent data, controlling

connected units or operating the unit with a terminal program.

The serial interface supports the RS-232, RS-422 and RS-485 transmission standards. The

mode used depends on the current configuration. Connection is via the terminal block.

Further topics:

–

Section 5.40 Advanced Mode: COM1, page 76

–

Section 8.8 Terminal block, page 109

8.8

Terminal block

The terminal block has several contacts for:

–

4 alarm inputs

–

1 relay output

–

Serial data transmission

Pin assignment serial interface

The pin assignment of the serial interface depends on the interface mode used.

Further topics:

–

Section 5.40 Advanced Mode: COM1, page 76

Pin assignment I/O

Link

Ethernet link type

Uplink, speed of the outgoing data traffic

Downlink, speed of the incoming data traffic

Contact

RS-232 mode

RS-422 mode

RS-485 mode

CTS

—

RxD- (receive data minus)

—

TXD

TxD (transmit data)

TxD- (transmit data minus)

Data-

RTS

—

TxD+ (transmit data plus)

Data+

RXD

RxD (receive data)

RxD+ (receive data plus)

—

GND

GND (ground)

—

Contact

Function

IN1

Input alarm 1

IN2

Input alarm 2

IN3

Input alarm 3

Summary of Contents for VJT-X20XF-E





























































































































Search results

Summary of Contents for VJT-X20XF-E

Reviews:

Related manuals for VJT-X20XF-E

Brands by name

Popular brands

Bosch VJT-X20XF-E, Installation And Operating Manual

Search results

Summary of Contents for VJT-X20XF-E

Reviews:

Related manuals for VJT-X20XF-E

Brands by name

Popular brands