Bosch Rexroth IndraDrive C HCS03.1 Planning Manual Download Page 28

Page: 28 / 86

4-2

Identification

Rexroth IndraDrive C HCS03.1

DOK-INDRV*-HCS03.1****-PR02-EN-P

4.2 Type

Plates

Each drive component is marked by a type designation.

There is a type plate attached to all devices.

A label (cable mark) is wrapped around ready-made cables. This label
indicates the type designation and the length. (The designation of the
cable itself - without connector - is printed on the cable sheath.)

The identification of accessories packed in bags is either printed on the
bag or indicated in an accompanying note.

Type Plate Arrangement

1: Power section type plate
2: Control section type plate
Fig. 4-2: Type plate arrangement

Summary of Contents for Rexroth IndraDrive C HCS03.1























































































Search results

Summary of Contents for Rexroth IndraDrive C HCS03.1

Reviews:

Related manuals for Rexroth IndraDrive C HCS03.1

Brands by name

Popular brands

Bosch Rexroth IndraDrive C HCS03.1, Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive C HCS03.1

Reviews:

Related manuals for Rexroth IndraDrive C HCS03.1

Brands by name

Popular brands