Bosch Rexroth IndraDrive C HCS03.1 Planning Manual Download Page 68 | Manualshive

Page: 68 / 86

background image

8-2

Replacing Devices

Rexroth IndraDrive C HCS03.1

DOK-INDRV*-HCS03.1****-PR02-EN-P

Replacing the Motor

•

open main switch

•

make sure main switch cannot be switched on again

•

disconnect plug-in connectors

Note:

When replacing the motor, cover the open mating sites of
power lines with protective caps if sprinkling with cooling
liquid/lubricant or soiling may occur (allowed degree of soiling
according to EN50178: 2).

•

replace

motor

Note:

To mechanically replace the AC servo motor, observe the
instructions of the machine manufacturer.

•

connect plug-in connectors

ATTENTION

Risk of accident due to accidental axis
movement!

⇒

Servo axes with indirect distance measuring system
via the motor encoder will loose the position data
reference when the motor is replaced!
This position data reference to the machine
coordinate system must therefore be reestablished
after replacement.

•

for servo axes with absolute motor encoder, reestablish the position

data reference

«
...
66
67
68
69
70
...
»

Summary of Contents for Rexroth IndraDrive C HCS03.1























































































Reviews:

No comments

Related manuals for Rexroth IndraDrive C HCS03.1

Brand: ABB Pages: 2

Brand: Eaton Pages: 16

Brand: GE Pages: 8

medialon Showmaster Go

Brand: 7th Sense Pages: 2

Brand: Campbell Pages: 8

Brand: Campbell Pages: 22

Brand: Danfoss Pages: 85

VLT Decentral FCD 300

Brand: Danfoss Pages: 112

Brand: Danfoss Pages: 4

VLT 6000 series

Brand: Danfoss Pages: 27

Brand: Danfoss Pages: 16

Brand: Danfoss Pages: 20

ADAP-KOOL AK-PC 781

Brand: Danfoss Pages: 14

Brand: Danfoss Pages: 12

Brand: Danfoss Pages: 12

vlt soft starter mcd 500

Brand: Danfoss Pages: 96

Brand: Samson Pages: 73

Brand: Hama Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands