Bosch Rexroth IndraDrive C HCS03.1 Planning Manual Download Page 10

Page: 10 / 86

1-4

Indroduction

Rexroth IndraDrive C HCS03.1

DOK-INDRV*-HCS03.1****-PR02-EN-P

Power Section

The following are connected to the power section:

•

mains

voltage

•

motor

•

24 V power supply (optional)

•

module bus (for cross communication in the case of DC bus

connection with other devices)

•

motor holding brake (optional)

•

motor temperature sensor (optional)

•

braking resistor (optional)

Control Section

The control section is a separate component that is plugged into the
power section. The drive controller is supplied ex works complete with
control section.

The control section may only be replaced by qualified personnel.

The contacts X31/1 and X31/2 are connected to the control section as Bb
contacts.

Note:

The control sections are described in a separate
documentation (see page 1-2).

Summary of Contents for Rexroth IndraDrive C HCS03.1























































































Search results

Summary of Contents for Rexroth IndraDrive C HCS03.1

Reviews:

Related manuals for Rexroth IndraDrive C HCS03.1

Brands by name

Popular brands

Bosch Rexroth IndraDrive C HCS03.1, Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive C HCS03.1

Reviews:

Related manuals for Rexroth IndraDrive C HCS03.1

Brands by name

Popular brands