Bosch Rexroth IndraDrive C HCS03.1 Planning Manual Download Page 67 | Manualshive

Page: 67 / 86

background image

Rexroth IndraDrive C HCS03.1

Replacing Devices

8-1

DOK-INDRV*-HCS03.1****-PR02-EN-P

8 Replacing

Devices

8.1 General

Information

The diagnostic display enables aimed and effective troubleshooting in
order to:

•

avoid production downtimes due to extensive searches in individual

devices and repairs of devices in the installation.

•

start operating the installation again without extensive assembly and

adjustments.

•

quickly eliminate the problem and easily replace defective drive

components.

When returning a defective device to our Customer Service, please
enclose the completed Fault Report. The Fault Report is included in this
chapter and may be copied for your convenience.

Note:

The new drive component must have the same type
designation as the faulty device. To ensure this, indicate the
entire type designation when requesting replacement parts.

8.2

How to Proceed When Replacing Devices

Note:

For replacing devices you absolutely have to observe the
safety instructions contained in chapter 3!

Replacing the Drive Controller

•

save parameter set

•

open main switch

•

make sure main switch cannot be switched on again

•

make sure drive controller is completely de-energized

DANGER

Lethal electric shock caused by contact to live
parts!

⇒

Before touching live parts allow the capacitors to

discharge! Only then start working on the connection
cables!

•

remove touch guard and separate connecting lines from drive

controller

•

unscrew screws on top and bottom of housing

•

take drive controller out of drive system

•

mount new drive controller

•

connect new drive controller as specified in machine circuit diagram

•

mount touch guard

•

copy firmware and parameter set to new drive controller (see firmware

documentation)

«
...
65
66
67
68
69
...
»

Summary of Contents for Rexroth IndraDrive C HCS03.1























































































Reviews:

No comments

Related manuals for Rexroth IndraDrive C HCS03.1

Brand: Jafar Pages: 10

Brand: Jafar Pages: 8

Brand: Balboa Instruments Pages: 10

Brand: Quantum Data Pages: 36

Brand: Daikin Pages: 2

Brand: Daikin Pages: 12

Brand: Daikin Pages: 12

Brand: Daikin Pages: 46

Brand: Daikin Pages: 21

Brand: Daikin Pages: 20

Brand: Fairchild Pages: 2

Brand: Fairford Pages: 233

Brand: Parker Pages: 44

Brand: National Instruments Pages: 14

Brand: National Instruments Pages: 31

Brand: National Instruments Pages: 50

Brand: National Instruments Pages: 24

Brand: National Instruments Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands