Bosch Rexroth ID 200/C-PDP Manual Download Page 13

Page: 13 / 84

Product description 13/84

3 842 540 399/2016-11, MIT: ID 200,

Bosch Rexroth AG

4.1.4

Manual operating unit/USB antenna

The following write/read devices are available for process control (write/read
functions, initialization of data carriers).

Write/read device

Frequency range

DPS/L (USB antenna for notebooks)

125 kHz

DPS/H (manual operating unit (Fig.6)

13.56 MHz

Fig. 5: Manual operating unit/USB antenna

4.2 Accessories for connection

4.2.1

Communication module connection cable to antennas and trigger sensors

Suitable antenna cables are available for connecting the antennas and trigger
sensors (Fig. 6).

Accessories

Designation

Length 2 m (socket straight, plug angled)

ID 200/K-ANT 2-2M

Length 5 m (socket straight, plug angled)

ID 200/K-ANT 2-5M

Length 2 m (socket and plug angled)

ID 200/K-ANT 3-2M

Length 5 m (socket and plug angled)

ID 200/K-ANT 3-5M

Fig. 6: Antenna cable

GLISH

Summary of Contents for Rexroth ID 200/C-PDP





















































































Search results

Summary of Contents for Rexroth ID 200/C-PDP

Reviews:

Related manuals for Rexroth ID 200/C-PDP

Brands by name

Popular brands

Bosch Rexroth ID 200/C-PDP, Manual

Search results

Summary of Contents for Rexroth ID 200/C-PDP

Reviews:

Related manuals for Rexroth ID 200/C-PDP

Brands by name

Popular brands