Bosch Rexroth ID 200/C-PDP Manual Download Page 55

Page: 55 / 84

Communication with ID 200/C-PDP 55/84

3 842 540 399/2016-11, MIT: ID 200,

Bosch Rexroth AG

7.3.9

Error/status messages

Status

Meaning

00h

The command was executed without errors.

FFh

The command is being processed.

Error messages triggered by the identification system

Status

Meaning

01h

reserved

02h

reserved

03h

reserved

04h

The command is incorrect or incomplete, or the parameter is
not in the valid range.

05h

There is no data carrier in the detection area.

06h

Hardware error, e.g. error during self-test or antenna faulty.

07h

This is an internal device error.

08h

reserved

09h

The parameterized data carrier type does not match the connected antenna.

0Ah

reserved

0Bh

reserved

0Ch

reserved

0Dh

reserved

0Eh

reserved

0Fh

reserved

Error messages triggered by the bus interface

Status

Meaning

10h

reserved

20h

reserved

40h

The command is incorrect or incomplete, or the parameter is
not in the valid range.

60h

Hardware error, e.g. no communication with the identification system.

70h

This is an internal device error.

GLISH

Summary of Contents for Rexroth ID 200/C-PDP





















































































Search results

Summary of Contents for Rexroth ID 200/C-PDP

Reviews:

Related manuals for Rexroth ID 200/C-PDP

Brands by name

Popular brands

Bosch Rexroth ID 200/C-PDP, Manual

Search results

Summary of Contents for Rexroth ID 200/C-PDP

Reviews:

Related manuals for Rexroth ID 200/C-PDP

Brands by name

Popular brands