Bosch D7412GV2 Program Entry Manual Download Page 45 | Manualshive

Page: 45 / 148

background image

D9412GV2/D7412GV2 |

Program Entry Guide | 2.0

GV2MAIN

EN

| 45

Bosch Security Systems | 5/05 | F001U003636B

Parameter Setup Requirement:

The Early Ambush timer can be started and stopped
only by pass codes with the L## Passcode Disarm
authority.

To avoid unintended results for the end
user of the system:

•

When a keypad is assigned to an area
that has the Early Ambush feature
enabled, set the

CC# Scope

value to

Area Wide.

•

If an area has

A# Two Man Rule

set to

Yes

, do not set

A# Early Ambush

to

Yes

.

During an alarm, after the first pass code is entered,
the Early Ambush timer still begins. A Cancel Report
might be generated, depending upon the bell time, and
the keypad displays

Alarm Silenced

normally. If

the second valid disarm pass code is entered, the
keypads indicate that the second pass code is valid.
Refer to the

Secondary Ambush Code

prompt on

page 132 for information about the unique behavior of
the two pass codes.

2.10 Keypad (Command Center)

This programming module contains three
programming categories: Cmd Cntr Assignment, Area
Text, and Custom Function.

2.10.1 Keypad (Command Center) Assignment

This programming category assigns a keypad to an
area and determines if the keypad is supervised. The
keypads are connected to the control panel using a
two-wire serial data interface (SDI) bus.

This bus can support up to eight supervised keypads,
each with its own unique keypad address (CC) and
corresponding DIP switch address settings. If the
keypads are not supervised, you can install multiple
keypads with the same DIP switch address setting for
up to 32 unsupervised keypads.

Cmd Center

Default:

1

Selection:

1 to 8

DIP Switch Setting

SDI
CC#

Address
Number

1 2 3 4 5 6

1

1

ON ON ON ON -- ON

2

2

OFF ON ON ON -- ON

3 3

ON OFF ON ON

--

ON

4 4

OFF OFF ON ON

--

ON

5 5

ON ON OFF ON -- ON

6 6

OFF ON OFF ON -- ON

7 7

ON OFF OFF ON

--

ON

8 8

OFF OFF OFF ON

--

ON

Enter the keypad (CC) number for the SDI address you are programming. This number corresponds to the DIP
switch address settings shown.

«
...
43
44
45
46
47
...
»

Summary of Contents for D7412GV2





















































































































































Reviews:

No comments

Related manuals for D7412GV2

Brand: NEC Pages: 146

Brand: Campbell Pages: 3

Brand: Parker Pages: 44

Brand: hager Pages: 62

coviva Smartbox TKP100A

Brand: hager Pages: 45

Brand: VAT Pages: 27

Brand: ICP DAS USA Pages: 148

Brand: ICMA Pages: 8

Gemini GEM-P9600

Brand: NAPCO Pages: 6

Gemini GEM-P816

Brand: NAPCO Pages: 56

Brand: OJ Electronics Pages: 8

Brand: OJ Electronics Pages: 112

Brand: OJ Pages: 17

Brand: vacuubrand Pages: 12

Brand: Vacon Pages: 47

Brand: Vacon Pages: 40

SMARTSTART 6000

Brand: Zener Pages: 36

Brand: Zapi Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands