Bosch D7412GV2 Program Entry Manual Download Page 104

Page: 104 / 148

D9412GV2/D7412GV2 |

Program Entry Guide | 5.0

RADXSKED

| 104

Bosch Security Systems | 5/05 | F001U003636B

W# Xept Holiday

Default:

Selection:

Yes or No

Yes

Do not activate this window on
holidays.

To use this selection, the window must
be programmed to activate on at least
one day of the week and a Holiday
Index must be enabled.

A holiday does not prevent this
window from activating.

You also use this selection if Opening
or Closing Windows are needed only
on certain days of the year. Do not
program the windows to execute on
any days of the week. Instead,
program

Xept Holiday

, and

select at least one Holiday Index with
the days of the year you want the
window to be active.

Determine if the window is disabled on holidays, or is
active only on holidays.

To prevent the windows from activating on certain
days of the year, program

Xept Holiday

Yes

, and

enable at least one Holiday Index. When

Xept

Holiday

is programmed as

Yes

, the window executes

on the days of the week programmed unless the date is
designated as a Holiday by the Holiday Index(es)
selected.

Holiday Indexes for O/C Windows

You can enable up to four Holiday Indexes for use
with Opening/Closing Windows. Enable at least one
Holiday Index if

W# Xept Holiday

is programmed as

Yes

for this window, or if you want this window to

activate only on specific dates. Holidays are
programmed in

Section 5.3 Holiday Indexes

on page 117.

W# Holiday 1

Default:

Selection: Yes or No

Yes

Use Holiday Index 1 with this
window.

Do not use Holiday Index 1 with this
window.

W# Holiday 2

Default:

Selection: Yes or No

Yes

Use Holiday Index 2 with this window.

Do not use Holiday Index 2 with this
window.

W# Holiday 3

Default:

Selection:

Yes or No

Yes

Use Holiday Index 3 with this
window.

Do not use Holiday Index 3 with this
window.

W# Holiday 4

Default:

Selection:

Yes or No

Yes

Use Holiday Index 4 with this window.

Do not use Holiday Index 4 with this
window.

W# Area 1 [through 8]

Default:

Selection:

Yes or No

Yes

Activate the window in the area
number (#) specified.

Disable the window in the area
number (#) specified.

Eight separate program items determine whether a
particular window activates in each of the eight areas
of the control panel.

Summary of Contents for D7412GV2





















































































































































Search results

Summary of Contents for D7412GV2

Reviews:

Related manuals for D7412GV2

Brands by name

Popular brands

Bosch D7412GV2, Program Entry Manual

Search results

Summary of Contents for D7412GV2

Reviews:

Related manuals for D7412GV2

Brands by name

Popular brands