Bosch D7412GV2 Program Entry Manual Download Page 146

Page: 146 / 148

D9412GV2/D7412GV2 |

Program Entry Guide | Programming Prompts Directory

| 146

Bosch Security Systems | 5/05 | F001U003636B

9133 Supervision ...................................120

RTS Control...........................................120

DTR Control..........................................120

Status Rate ..............................................120

SDI RPS Parameters

..................................121

User Interface Modifications for COMMAND 43121

Enable SDI RPS ....................................121

Call Back Enabled .................................121

RPS IP Address 1 ..................................122

RPS IP Address 2 ..................................122

RPS IP Address 3 ..................................122

RPS IP Address 4 ..................................122

Using an External Modem ............................123

Enable Ext Modem ...............................126

Answer Armed.......................................126

Answer Disarmed ..................................126

RPS Line Monitor .................................126

Seize Relay .............................................126

Modem Init String .................................126

RPS Dial String......................................126

Programming Path Numbers and IP Addresses
for Enhanced Communications...............127

Enhanced Comm...................................127

Path # IP Add1......................................127

Path # IP Add2......................................127

Path # IP Add3......................................127

Path # IP Add4......................................127

Path # Poll Rate.....................................128

Path # Ack Wait ....................................129

Path # Retry Count...............................129

SDI RPS/Enhanced Communications
Configuration

.....................................................130

Baud Rate ...............................................130

Parity/Stop..............................................130

RTS Control...........................................130

DTR Control..........................................130

9133 Supervision ...................................131

Base Port Number .................................131

Route Group Attempts ..................................131

RG# 1 Attempt......................................131

Miscellaneous

..............................................131

Fire Supv Res Type...............................131

Enable Protocol Type ........................... 131

Enable Anti Replay............................... 131

Fire Trouble Resound........................... 132

Early Ambush Timer ............................ 132

Secondary Ambush Code..................... 132

Cross Point Parameters............................. 132

Cross Point Time................................... 133

RADXAXS .......................................................... 135

Door Profile ................................................. 135

Door # .................................................... 135

D# Entry Area # ................................... 135

D#CC#Scope ........................................ 135

D# Custom Function ............................ 135

D# Door Point....................................... 136

D# Interlock Point ................................ 136

D# Auto Door? ..................................... 137

D# Fire Unlock?.................................... 137

D# Disarm on Open? ........................... 137

D# Card Type ....................................... 137

Strike Profile ............................................... 138

Door # .................................................... 138

D# Strike Time...................................... 138

D# Shunt Time...................................... 138

D# Buzz Time ....................................... 138

D# Extend Time ................................... 138

D# Deact On Open? ............................ 139

D# RTE Shunt Only?........................... 139

D# REXShunt Only?............................ 139

Event Profile................................................ 139

Door # .................................................... 139

D# Access Granted? ............................. 140

D# No Entry? ........................................ 140

D# Enter Request?................................ 140

D# Exit Request? .................................. 140

Summary of Contents for D7412GV2





















































































































































Search results

Summary of Contents for D7412GV2

Reviews:

Related manuals for D7412GV2

Brands by name

Popular brands

Bosch D7412GV2, Program Entry Manual

Search results

Summary of Contents for D7412GV2

Reviews:

Related manuals for D7412GV2

Brands by name

Popular brands