Bosch D7412GV2 Program Entry Manual Download Page 60 | Manualshive

Page: 60 / 148

background image

D9412GV2/D7412GV2 |

Program Entry Guide | 2.0

GV2MAIN

EN

| 60

Bosch Security Systems | 5/05 | F001U003636B

Move to Area

Default:

P

Selection:

Blank, E, or P

Function No.

Function Name

Alternate Keystroke

30

Move to Area

[COMMAND][5][0]

Use this function to switch the keypad’s assignment
temporarily to a different area. This command can be
used to perform any function that can be performed
by a keypad assigned to the area in programming.

Users are limited to performing functions enabled by
the authority level they have in the area to which the
keypad is moved. After 15 seconds of no activity at the
keypad, the keypad reverts back to the originally
programmed area.

Display Rev

Default:

E

Selection:

Blank, E, or P

Function No.

Function Name

Alternate Keystroke

32 Display

Software

Revision

[COMMAND][5][9]

Use this function to show the control panel’s software
revision number in the keypad display.

Service Walk

Default:

P

Selection:

Blank, E, or P

Function No.

Function Name

Alternate Keystroke

33 Service

Walk

Test

(Menu function only)

Use this function to Walk Test all 246 points in the
entire control panel regardless of the

P## Type

.

The Service Walk Test is available on the
D9412GV2 using the Service Menu
[9][9][ENT]. The D7412GV2

does not

include the Service Walk Test in the
Service Menu. In the D7412GV2, the
Service Walk Test function must be
enabled in the Function List to access the
Service Walk Test.

Default Text

Default:

P

Selection:

Blank, E, or P

Function No.

Function Name

Alternate Keystroke

34 Default

Text

[COMMAND][5][7]

Determining the armed state of an area using the
programmed custom text might be difficult. Use this
function to switch temporarily to the control panel
default text, shown on the program record sheet.

Change Skeds

Default:

P

Selection:

Blank, E, or P

Function No.

Function Name

Alternate Keystroke

35 Change

Skeds

[COMMAND][5][2]

Execute this panel-wide function from any keypad
assigned to an area where the user has authority. Use
this function to change the

S## Time

from the keypad

to make adjustments to Skeds.

#36 Invisible Walk Test

Default:

P

Selection:

Blank, E, or P

This function allows a user with the

L## Invisible

Walk Test

authority to test invisible interior or

perimeter controlled points that are within the scope of
the keypad, without sending reports to the central
station. Invisible points must have the

P## Invisible

Pt

function programmed

Yes

.

«
...
58
59
60
61
62
...
»

Summary of Contents for D7412GV2





















































































































































Reviews:

No comments

Related manuals for D7412GV2

Brand: S&C Pages: 40

Brand: B&G Pages: 2

Brand: B&K Pages: 9

Brand: National Instruments Pages: 2

Brand: Radware Pages: 98

Brand: RabbitCore Pages: 34

Brand: GEM Pages: 17

Brand: Belimo Pages: 2

Brand: Watts Pages: 12

Brand: Hunter Pages: 2

Brand: jablotron Pages: 12

8745 MFC Ethernet

Brand: Burkert Pages: 70

Brand: Tempco Pages: 12

Brand: Vixen Horns Pages: 2

Brand: Kele Pages: 33

Brand: Scott Edwards Electronics Pages: 10

GL8-GL8000M3-RCA-3.0

Brand: Balboa Instruments Pages: 9

Brand: YASKAWA Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands