Bosch D7412GV2 Program Entry Manual Download Page 16

Page: 16 / 148

D9412GV2/D7412GV2 |

Program Entry Guide | 2.0

GV2MAIN

| 16

Bosch Security Systems | 5/05 | F001U003636B

Burglar Reports

Select

Yes

to send a report when the event occurs.

Table 9: Burglar Reports

Report Selections

Report Description

R# Alarm

Yes

Burglar Alarm Event

R# Burg
Restore

Yes

Non-fire restoral from
trouble, missing, or
supervisory

R# Duress

Yes

Duress

R# Missing
Alarm

Yes

Missing Alarm point

R# Usr Code
Tmpr

Yes

User code tamper

R# Trouble
Rpt

Yes

Trouble Event

R# Missing
Trbl

Yes

Missing Trouble Event

R# Non Fire
Suprv

Yes

Non-fire Supervision
Event

R# Pt Bus Fail

Yes

Point bus failure

R# Pt Bus
Rstl

Yes

Restoral of point bus
after failure

R# Non Fire
Cncl

Yes

Canceled non-fire
alarm

R# Alarm
Restore

Yes

Non-fire restoral from
alarm

R# Sup
Missing

Yes

Supervisory missing

Unverified

Evt

∗

Yes,

Unverified Events for
Cross Points

∗

R# Unverified

Evt

is not reported when using BFSK

format. Additionally, this event does not produce a
corresponding Restoral event

R# Unverified Evt

is sent when a single

point programmed in Cross Point Group
faults into an alarm condition, then restores
before the Cross Point Time elapses.

R# Unverified Evt

encompasses both Fire

and Non-fire points, but is not related to the

A# Verify Time

used for smoke detectors.

The 9000GV2 Series control panels log a
Ground Fault Event as Trouble Point 256.

Restoral Reports are not sent if the
control panel resets after a point is
bypassed and then unbypassed. This is
true for both Fire and Non-fire points.

User Reports

Selecting

Yes

enables a report to be sent when the

event occurs.

Table 10: User Reports

Report Selections

Report

Description

R# Point
Bypass

Yes

, No

Point Bypass Event

R# Forced
Point

Yes

, No

Forced Point Event

R# Point
Open

Yes

, No

Point Opening Event

R# Point
Close

Yes

, No

Point Closing Event

R# Forced
Arm

Yes

, No

Point Force Armed

R# Fail To
Open

Yes

, No

Fail to Open Event

R# Fail To
Close

Yes

, No

Fail to Close Event

R# Ext Clos
Tm

Yes

, No

Extend Close Time
Event

R# Opening
Rpt

Yes

, No

Opening Events

R# Forced
Close

Yes

, No

Point Forced Close
Event

R# Closing
Rpt

Yes

, No

Closing Events

R# FC Perim
Inst

Yes

, No

Forced Close
Perimeter Instant
Armed Event

R# FC Perim
Delay

Yes

, No

Forced Close
Perimeter Delay
Armed Event

R# Perim Inst
Arm

Yes

, No

Perimeter Instant
Armed Event

R# Perim
Delay Arm

Yes

, No

Perimeter Delay
Armed Event

R# Send User
Text

Yes

, No

User text

Summary of Contents for D7412GV2





















































































































































Search results

Summary of Contents for D7412GV2

Reviews:

Related manuals for D7412GV2

Brands by name

Popular brands

Bosch D7412GV2, Program Entry Manual

Search results

Summary of Contents for D7412GV2

Reviews:

Related manuals for D7412GV2

Brands by name

Popular brands