Black+Decker CS1840, Original Instructions Manual

Page: 9 / 124

9
ENGLISH (Original instructions)
Electrical safety
#
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
‹
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Using an extension cable
‹
Always use an approved extension cable suitable for the
power input of this tool (see technical data). The extension
cable must be suitable for outdoor use and marked ac-
FRUGLQJO\251);PPðH[WHQVLRQ
cable can be used without loss of product performance.
Before use, inspect the extension cable for signs of
damage, wear and ageing. Replace the extension cable
if damaged or defective. When using a cable reel, always
unwind the cable completely.
Voltage drops
‹
Under certain power supply conditions this product may-
cause short-time voltage drops during start-up.
‹
Other equipment may be affected. For example, electri-
clights may temporarily reduce in brightness.
‹
Contact the supply authority, if necessary, to determine
that the impedance of the power supply is lower than
366
RKPV'LVWXUEDQFHVDUHXQOLNHO\WRRFFXUXQGHUWKLV
condition.
Guard against electric shock
‹
Prevent body contact with earthed or grounded surfaces
(e.g. metal railings, lamp-posts etc.). Electric safety can
EHIXUWKHULPSURYHGE\XVLQJDKLJKVHQVLWLYLW\P$
30mS) Residual Current Device (RCD).
:
Warning!
The use of an RCD or other circuit
breaker unit does not release the operator
of your chainsaw from the safety instructions
and safe working practices given in this user
manual.
Features
2QRIIVZLWFK
2. Lock-off button
)URQWJXDUGFKDLQEUDNHDVVHPEO\
4. Guide bar
5. Chain
6. Chain cover assembly
&KDLQDGMXVWORFNLQJQXWFRYHU
&KDLQWHQVLRQDGMXVWPHQWQXW
9. Chain sheath
3RZHUFRUG
3RZHUFRUGUHWDLQHU
2LOFDS
2LOOHYHOLQGLFDWRU
Assembly
@
Warning!
Always wear protective gloves when
working on your chainsaw.
@
Warning!
Before performing any assembly
or maintenance on power tools, switch off and
remove the battery.
@
Warning!
Remove the cable tie that attaches
the chain to the chainbar before assembly.
Oiling the chain
You must do this whenever you use a new chain (6) for the
¿UVWWLPH7DNHWKHQHZFKDLQDQGVRDNLWLQFKDLQRLOIRUDW
least an hour before using it. Use BLACK+DECKER chain oil.
We recommend that you use only BLACK+DECKER oil during
the lifetime of your chainsaw because mixtures of different oils
could lead to the oil becoming degraded, which can drastically
shorten the lifetime of the saw chain and create additional
risks.
Never use waste oil, thick oil or very thin sewing machine oil.
These may damage your chainsaw.
)LWWLQJWKHJXLGHEDUDQGFKDLQÀJ$+
‹
Place the chainsaw onto a stable surface.
‹
5HPRYHWKH&KDLQDGMXVWORFNLQJQXWFRYHU¿J%
‹
5RWDWHWKHFKDLQDGMXVWORFNLQJQXWZLWKWKHVSDQQHU
VFUHZGULYHUWRROSURYLGHGFRXQWHUFORFNZLVHWRUHPRYH
WKHFKDLQFRYHUDVVHPEO\¿J&
‹
Place the chain (5) over the guide bar (4) making sure that
the saw chain cutters on the upper part of the guide bar
IDFHWRZDUGVWKHIURQW¿J(
‹
5RWDWHWKHFKDLQWHQVLRQDGMXVWPHQWQXWZLWKWKHVSDQQHU
VFUHZGULYHUWRROSURYLGHGFRXQWHUFORFNZLVHWR$OORZ
PRYHPHQW¿J'
‹
Guide the chain (5) around the guide bar (4) and pull it to
create a loop to one side at the rear end of the guide bar
(4).
‹
*XLGHWKHFKDLQDURXQGWKHGULYHVSURFNHWOLQHXS
the bottom hole in the guide bar and the chain tensioning
EROW¿J)
Note:
rotate chain tensioning nut as necessary to line centre
KROHZLWKEROW
Warning!
0DNHVXUHWKDWWKHIURQWJXDUGFKDLQEUDNHDVVHP
-
EO\LVLQWKHVHWIRUZDUGSRVLWLRQEHIRUHUH¿WWLQJ¿J$
‹
Place the chain cover assembly (6) onto the chainsaw.
‹
0DNHVXUHWKDWWKHWDERQWKHFKDLQFRYHUDVVHPEO\
ORFDWHVFRUUHFWO\LQWRWKHVORWRQWKHPDLQKRXVLQJ¿J
G).
‹
5RWDWHWKHFKDLQDGMXVWORFNLQJQXWFORFNZLVHXQWLO
snug.
‹
/RRVHQWKHFKDLQDGMXVWORFNLQJNQRERQHIXOOWXUQVR
the chain can be tensioned.
‹
Check the tension as described below. Do not overtighten.
‹
7LJKWHQWKHFKDLQWHQVLRQDGMXVWPHQWQXWZLWKWKH
VUHZGULYHUVSDQQHUSURYLGHG¿J+&KDLQJXLGHEDU
indicated with dotted lines)