Black Box SW542A Manual Download Page 53

Page: 53 / 64

CHAPTER 9: Command Reference Guide

9.3 Command Summary

The chart below summarizes all the commands available with the Serial Console
Port Manager.

Command Availability

Function

Command Syntax

Supervisor

User

Enter Command Mode

[Enter]

√

Exit Command Mode

/X [Enter]

√

Help Menu

/H [Enter]

√

Display Site ID

/J [Enter]

√

Display Port Status

/S[P] [Enter]

√

1, 2

√

Display Port Diagnostics

/SD [Enter]

√

Display Port Parameters

/W[P] xx [Enter]

√

Set System Parameters

/F [Enter]

√

Set Port Parameters

/P xx [Enter]

√

Copy Port Parameters

/CP [Enter]

√

Connect

/C xx [yy] [Enter]

√

Resident Disconnect5

[Enter]+++[Enter]

√

Third-Party Disconnect6

/D[/Y] xx [yy] [Enter]

√

/D[/Y] * [Enter]

Erase Buffer

/E[/Y] xx [yy] [Enter]

√

/E[/Y] * [Enter]

Default and Test

/I[/Y] [Enter]

√

Save Parameters

/U [Enter]

√

1Supervisor Mode displays parameters for all ports; User Mode only displays

parameters for ports allowed by Port Password.

2Supervisor Mode only: Include the “P” in the “SP” or “WP” command to display

ports’ passwords.

3A port with “User” command capability can only view its own parameters. A User

Port

cannot

view parameters for other ports.

4A User Port

cannot

perform a Third-Party Connect.

5Resident Disconnect: Disconnects your resident port from another port. Note that

the Resident Disconnect Sequence can be redefined through the Port
Configuration menus.

6Third-Party Disconnect: Disconnects two or more nonresident ports. Must be

issued from a third port with Supervisor command capability.

Summary of Contents for SW542A
































































Search results

Summary of Contents for SW542A

Reviews:

Related manuals for SW542A

Brands by name

Popular brands

Black Box SW542A, Manual

Search results

Summary of Contents for SW542A

Reviews:

Related manuals for SW542A

Brands by name

Popular brands