Black Box SW542A Manual Download Page 31 | Manualshive

Page: 31 / 64

background image

29

CHAPTER 5: Configuration

The Port Configuration menu offers the following options:

1. Port Name

(up to 16 characters, undefined by default): Assigns a name to the

port.

2. Password

(up to 16 characters, undefined by default): Defines the Port

Password for this port. Note that identical Port Passwords are generally
assigned to several ports. When this password is entered at the login prompt,
the user will then have access to all ports that share this password.

NOTES

The Port Password is not displayed by the Port Parameters menu. When
the Port Password has been defined, the field for this item will read
“defined.” To display Port Passwords, invoke the /SP or /WP commands
as described in

Chapter 6

.

The Port Manager will not allow you to define a Port Password which is
the same as the existing Supervisor Password.

3. Baud Rate:

Selects the baud rate for the port. Can be set to any standard rate

from 300 to 115.2 kbps. The default value is the baud rate selected with Setup
Switches 1 through 3 (see

Section 4.1.1

).

4. Bits/Parity:

Sets data bits and parity for this port. (The default value is 8 data

bits, no parity.)

5. Stop Bits:

Sets stop bits for this port. (The default value is 1 stop bit.)

6. Handshake Mode:

Selects the handshake format for this port. Can be set to

X-ON/X-OFF (software), RTS/CTS (hardware, the default value), both, or
none.

7. Port Mode:

Defines the operation mode for this port. The user can select Any-

to-Any Mode (the default value), Passive Mode, Buffer Mode, or Modem
Mode. Note that Ports 1 and 2

cannot

be configured for Passive Mode or Buffer

Mode.

When Any-to-Any, Passive, or Buffer Mode is selected, the Port Manager will

display the DTR Output prompt as shown in Figure 5-1 on the previous page.
The DTR Output prompt is not displayed when Modem Mode is selected.

74. DTR Output:

Determines how DTR will react when this port disconnects.

DTR can be held low, held high, or pulsed for 0.5 seconds and then held
high (the default value). For more information on DCD and DTR
hardware lines, please refer to the

Appendix

.

«
...
29
30
31
32
33
...
»

Summary of Contents for SW542A

































































Reviews:

No comments

Related manuals for SW542A

Brand: N-Tron Pages: 138

Brand: National Instruments Pages: 26

Brand: National Instruments Pages: 85

Module SCXI-1503

Brand: National Instruments Pages: 79

Brand: QNAP Pages: 20

Brand: Dahua Pages: 24

Brand: Planet Pages: 20

EK-FC1080 GTX Ti TF6

Brand: ekwb Pages: 2

Brand: Waves Pages: 41

Brand: Accom Pages: 15

Brand: National Instruments Pages: 130

Brand: A2B Electronics Pages: 24

Brand: ZALMAN Pages: 6

Brand: H3C Pages: 9

Sinus 154 data II

Brand: T-COM Pages: 12

Brand: Global Sun Pages: 39

Brand: Navitar Pages: 1

Brand: US Robotics Pages: 180

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands