Black Box SW542A Manual Download Page 48 | Manualshive

Page: 48 / 64

background image

46

SERIAL CONSOLE PORT MANAGER

7.4 Modem Mode

In addition to allowing data transfer, the Modem Mode also provides additional
functions specifically related to modem communication. A Modem Mode Port can
perform all functions normally available in Any-to-Any Mode. Any Serial Console
Port Manager port can be configured as a Modem Mode Port.

When the Modem Mode is selected, the Port Configuration menu (command /P)
will display three additional prompts which allow the user to redefine the modem
reset string, initialization string, and hangup string.

When the Modem Mode is selected for a port with Supervisor-Level command
access, the Supervisor Password should be defined. This will discourage
unauthorized access to higher command functions.

When a call is received, the Port Manager will prompt the caller to enter a
password. The Port Manager allows three attempts to enter a valid password. If the
correct password is not entered in three attempts, or if the user does not respond
to the password prompt within 30 seconds, the modem will disconnect.

The password can be defined and enabled by invoking the /P command as
described in

Section 5.5.3

.

NOTE

When a Modem Mode Port exits Command Mode, or if the DCD line is
lost while the Command Mode is active, the Serial Console Port
Manager will pulse the DTR line to the modem. The Port Manager will
then send the user-defined modem command strings to make certain
the modem is properly disconnected and reinitialized.

When an external modem is installed on a Port Manager port, other
ports can use the modem for calling out. To call out, invoke the /C
command to connect to the port, and then access the modem as you
normally would.

«
...
46
47
48
49
50
...
»

Summary of Contents for SW542A

































































Reviews:

No comments

Related manuals for SW542A

Express EtherNetwork DFE-670TXD

Brand: D-Link Pages: 4

Brand: DAD Pages: 36

Brand: D-Link Pages: 2

Brand: Lattice Semiconductor Pages: 15

iCE40 UltraLite

Brand: Lattice Semiconductor Pages: 13

Brand: SAF Pages: 30

AIE900-XNX Series

Brand: AXIOMTEK Pages: 53

Brand: ADTRAN Pages: 2

Brand: Promise Technology Pages: 26

Brand: Solwise Pages: 231

Brand: PADAUK Pages: 27

TeleMyo 2400T V2

Brand: Noraxon Pages: 52

Brand: AMG Pages: 4

Brand: Idis Pages: 40

Brand: netsys Pages: 243

Brand: H3C Pages: 4

Temporary Target Board M38517T-ADS

Brand: Renesas Pages: 14

Brand: Radionics Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands