Black Box SW542A Manual Download Page 57 | Manualshive

Page: 57 / 64

background image

55

CHAPTER 9: Command Reference Guide

/F — S

ET

S

YSTEM

P

ARAMETERS

Displays a menu which is used to define the Site ID message and Supervisor
Password. When the Supervisor Password is defined, the Serial Console Port
Manager will display a password prompt before allowing access to Command
Mode. For more information, refer to

Section 5.4

.

Availability:

Supervisor only.

Format:

/F

[Enter]

Response:

Displays System Parameters menu.

/H — H

ELP

Displays a Help screen, which lists all of the Serial Console Port Manager’s
commands along with a brief description of each command.

Availability:

Supervisor/User.

Format:

/H

[Enter]

Response:

Displays Help screen (the User-level Help screen does not include

information about Supervisor commands).

/I — D

EFAULT AND

T

EST

Tests internal memory and initializes the Port Manager with the default parameters
specified by the Setup Switches.

CAUTION

When the /I command is invoked, the Serial Console Port Manager will
revert to the parameters specified by the Setup Switches. Any
command-selected parameters will be lost.

Availability:

Supervisor only.

Format:

/I[/Y]

[Enter]

, where “/Y” optionally suppresses the “Sure?” prompt.

Response:

Verbose:

“Are you Sure (y/n)?” prompt, followed by memory test and
initialization if you type “

Y

”.

Terse:

5, followed by memory test and initialization if you type “

Y

”.

«
...
55
56
57
58
59
...
»

Summary of Contents for SW542A

































































Reviews:

No comments

Related manuals for SW542A

Network Card-MS

Brand: Eaton Pages: 89

Brand: Accusys Pages: 34

Brand: Patton electronics Pages: 9

Brand: Qlogic Pages: 8

Brand: ZALMAN Pages: 5

RouterBOARD 411R

Brand: 4gon Pages: 2

Brand: Gira Pages: 6

5200 Live Series EventCD

Brand: MF DIGITAL Pages: 21

IP-Logic ZIG-IPPRO-RX

Brand: Zigen Pages: 4

Brand: 3Com Pages: 53

Brand: iNetVu Pages: 20

See3CAM 30 Z10X

Brand: e-con Systems Pages: 14

Brand: Planet Pages: 2

Brand: ADTRAN Pages: 4

Brand: Linksys Pages: 80

Digital Loudspeaker

Brand: Dolby Laboratories Pages: 4

MP5S Plus Writer

Brand: SONIX Pages: 23

Brand: Freescale Semiconductor Pages: 124

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands