Black Box SW542A Manual Download Page 58 | Manualshive

Page: 58 / 64

background image

56

SERIAL CONSOLE PORT MANAGER

/J — D

ISPLAY

S

ITE

ID

Displays the user-defined Site ID message.

Availability:

Supervisor/User.

Format:

/J

[Enter]

Response:

Displays Site ID Message.

/P — S

ET

P

ORT

P

ARAMETERS

Displays a menu which allows you to select options and parameters for the selected
port.

Section 5.5.3

describes the procedure for defining port parameters.

Availability:

Supervisor only.

Format:

/P [xx]

[Enter]

, where “xx” is the number or name of the port to be

configured; if the port number or name is not specified, the Port Configuration
menu for your resident port will be displayed.

Response:

Displays Port Parameters menu.

/S — D

ISPLAY

P

ORT

S

TATUS

Displays the Port Status screen, which lists current conditions and parameters for
all ports. Normally, the Port Status screen will not display Port Passwords; the
Password column will read either “defined” or “undefined”, depending on whether
or not the password for each port has been specified. When the Supervisor Mode is
active, the /SP command offers the option to either display or suppress Port
Passwords. In User Mode, the /S command will only display information for the
ports that share the same password entered at login. For more information on the
Port Status screen, please refer to

Section 6.1

.

Availability:

Supervisor/User.

Format:

/S[P]

[Enter]

, where “P”, if included in a command sent from a

Supervisor port, causes the screen to list all defined port passwords.

Response:

Displays Port Status screen.

/SD — D

ISPLAY

P

ORT

D

IAGNOSTICS

Provides more detailed information regarding the operational status of each port.
Note that in User Mode, this screen will only display parameters for the ports that
are allowed by the Port Password that was entered at log in. For more information
on the Port Diagnostics screen, please refer to

Section 6.2

.

Availability:

Supervisor/User.

Format:

/SD

[Enter]

Response:

Displays Port Diagnostics screen.

«
...
56
57
58
59
60
...
»

Summary of Contents for SW542A

































































Reviews:

No comments

Related manuals for SW542A

AllShare Cast Dongle

Brand: Samsung Pages: 2

Brand: D-Link Pages: 14

Brand: D-Link Pages: 7

Brand: D-Link Pages: 41

Brand: F5 Pages: 2

Brand: F5 Pages: 90

Brand: F5 Pages: 47

Brand: Lattice Semiconductor Pages: 15

Brand: Watchguard Pages: 24

LinkSmart KW6515

Brand: Kasda Pages: 31

FireWire 800 + Hi-Speed USB Combo

Brand: SIIG Pages: 20

Brand: Zoom Pages: 48

Brand: Teletronics International Pages: 57

Brand: MFJ Pages: 11

Brand: Cypress Semiconductor Pages: 19

Brand: CAME Pages: 32

Brand: Neousys Technology Pages: 24

POD-51EH-C541U-12

Brand: IceTech Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands