Black Box SW542A Manual Download Page 27 | Manualshive

Page: 27 / 64

background image

25

CHAPTER 5: Configuration

5.4. Defining the Site ID and Supervisor Password

Before configuring individual ports, the Site ID and Supervisor Password should be
defined. The Site ID indicates the location or name of the Serial Console Port
Manager; the Supervisor Password restricts access to sensitive command functions.
The Site ID and Supervisor Password are defined using the System Parameters
menu (/F).

NOTES

The Site ID cannot include double quotes.

The Supervisor Password cannot include an asterisk, forward slash,
spaces, or double quotes.

Both the Site ID and Supervisor Password will be cleared if the Port
Manager is initialized to default settings.

The Port Manager will not allow you to select a Supervisor Password
that is the same as an existing Port Password.

The System Parameters Menu is only available in Supervisor Mode.

1. Access the Command Mode. Type

/F

and press

[Enter]

to display the System

Parameters Menu.

2. Site ID Message (up to 32 characters long; undefined by default): Type

1

(one) and press

[Enter]

; a prompt will appear. Key in the desired text and

press

[Enter]

. The Site ID will be listed on the Port Status and Port Diagnostic

screens.

3. Supervisor Password (up to 16 characters long; undefined by default) Type

2

and press

[Enter]

; a prompt will appear. Key in the desired password, then

press

[Enter]

. The Port Manager will prompt you to re-key the password to

confirm spelling and capitalization. Key in the password a second time, then
press

[Enter]

.

NOTES

The Supervisor Password is case sensitive. Make certain to note the
exact password entered, including the case of each letter.

Make certain to write down your Supervisor Password. If the password
is lost or forgotten, you will not be able to access Supervisor-Level
commands unless you initialize the unit and clear all parameters as
described in

Section 4.2

.

«
...
25
26
27
28
29
...
»

Summary of Contents for SW542A

































































Reviews:

No comments

Related manuals for SW542A

All in One Printer

Brand: Baracoda Pages: 42

DES-3526 - Switch - Stackable

Brand: D-Link Pages: 258

Brand: FabiaTech Pages: 4

Brand: Quatech Pages: 27

Brand: Patton electronics Pages: 75

RocketLink-G 3088/I

Brand: Patton electronics Pages: 61

Brand: Patton Pages: 12

Brand: Patton Pages: 84

OnSite 3210 Series

Brand: Patton Pages: 110

Brand: Patton electronics Pages: 2

SMARTNODE 4110 Series

Brand: Patton electronics Pages: 78

Brand: Patton electronics Pages: 8

iW-RainboW-G30D

Brand: iWave Pages: 89

Brand: Vivotek Pages: 170

Brand: Garland Pages: 43

Brand: Softing Pages: 4

Storage Networking (Unified Fabric Pilot)

Brand: Qlogic Pages: 76

Brand: WABCO Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands