Belarus 80.1 Series Operation And Service Manual Download

Page: 134 / 143

Belarus 80.1/80.2/82.1/82.2/82

Р —Operation and Service Manual

Section 10. Common troubles and their remedies

125

Table 14, continued

Trouble, External Symptoms

Remedy

With the Hitch in Operation, Oil Leaks through "Sleeve-King Pin Tube" Joining

Worn-out rubber O-springs.

Replace the O-rings.

Wheel toe-in settings disturbed.

Adjust the front wheel toe-in.

Enhanced Wear and Ply Separation of Front Wheel Tyres

Air pressure in front and rear tyres disagree with
recommended norms.

To ensure against malfunctions, maintain front and
rear tyre pressure within recommended norms.

Wheel toe-in adjustment disturbed.

Re-adjust toe-in.

Front axle is in constant forced engagement due
to break or jamming in the transfer case con-
trols.

Check FDA forced engagement. Remove faults, if
any. Re-adjust the transfer case control mecha-
nism.

10.3. STEERING CONTROL WITH HSB INSTALLED

Enhanced Steering Wheel Effort («Heavy» Steering) with HSB

Oil foam formation in the booster system due to:

(a) insufficient oil level in the HSB tank;
(b) air ingress into the system.

Check oil level, top up as necessary, if required;
Check the suction pipeline and restore leakproof-
ness.

Safety valve adjustment disturbed.

Adjust the valve.

Enhanced oil leakage in the HSB pump.

Replace the pump.

Sticking in «worm-sector» meshing.

Adjust worm-gear meshing.

Enhanced vibration of the steering.

Adjust the steering wheel.

Summary of Contents for 80.1 Series
















































































































































Search results

Summary of Contents for 80.1 Series

Reviews:

Related manuals for 80.1 Series

Brands by name

Popular brands

Belarus 80.1 Series, Operation And Service Manual

Search results

Summary of Contents for 80.1 Series

Reviews:

Related manuals for 80.1 Series

Brands by name

Popular brands