BEL Engineering HPBG Series User Manual Download Page 37

Page: 37 / 74

2. When the value of the calibration weight begins to flash, load the calibration weight on the

plate.

3. Wait for the calibrated weight to be displayed and the stability symbol to turn on, and then

remove the weight from the plate.

4. When

“0.000”

is shown on the display, press the

PRINT

button in a prolonged manner

until the beeping stops.

The acquisition and automatic storage of the internal weight will

now begin. During the acquisition cycle, the display will show the following flashing
writing:

5. Once the internal calibration has been stored, the balance will return to the normal

weighing condition.

6. Now re-enter the calibration menu as described in paragraph 9.1.12 and set the desired

internal, automatic, or external calibration modality.

ATTENTION : this procedure must be effected only using E1 class reference
masses.

Mem. Tech

01-06-10 13:15:24



200

01-06-10 13:15:24



-0-

Summary of Contents for HPBG Series











































































Search results

Summary of Contents for HPBG Series

Reviews:

Related manuals for HPBG Series

Brands by name

Popular brands

BEL Engineering HPBG Series, User Manual

Search results

Summary of Contents for HPBG Series

Reviews:

Related manuals for HPBG Series

Brands by name

Popular brands