BEL Engineering HPBG Series User Manual Download Page 23

Page: 23 / 74

After setting

Weight Units 1

(by pressing the

PRINT

button to confirm),

the screen

relative to the setup menu will be displayed again,

select “

Weight Units 2

” and press

PRINT

to confirm.

5. The "

Grams

" unit will be displayed. Pressing the

MENU

CAL

key will now be

possible to scroll backwards or forwards the secondary units menu.

6. Press the

PRINT

key to confirm or

MENU

to change to another unit of measurement

(the units of measurement available are the same as those listed in point 3).

7. To escape from parameters setup menu, press the

MENU

button until

the acoustic

alarm gets mute, then release the button.

8. The balance returns to normal weighing conditions.

Grams

Weight Units 2

Setup Menù

Weight Units 1

- Serial output
- Baud rate
- Auto zero

Weight Units 2

22-01-19 16:30:24

2 Sec

Summary of Contents for HPBG Series











































































Search results

Summary of Contents for HPBG Series

Reviews:

Related manuals for HPBG Series

Brands by name

Popular brands

BEL Engineering HPBG Series, User Manual

Search results

Summary of Contents for HPBG Series

Reviews:

Related manuals for HPBG Series

Brands by name

Popular brands