BEL Engineering HPBG Series User Manual Download Page 62

Page: 62 / 74

12.3 Connection of the Balance to computer

To receive/transmit data, link the connector of the balance to the serial port of your Personal
Computer as shown below:

There are three ways of transmission in which the Balance and the computer can be
interfaced:



Continuous transmission of weight data (continuous mode must be set from the menu
as explained in the paragraph 10.2).



On demand transmission of weight data (on demand mode must be set from the menu
as explained in the paragraph 10.2).



On demand transmission with GLP of weight data (on demand mode with GLP must
be set from the menu as explained in the paragraph 10.2).

In all the modes it is possible to execut

e all the balance’s functions directly from the

computer’s keyboard, transmitting to balance the ASCII codes as shown in the table below.

CODICE

FUNCTION

(PROLONGED

PRESS)

“t” = H74

TARE

“c” = H63

CALIBRATION

“e” = H65

ENTER

“m” = H6D

“o” = H6F

ON/OFF

CODE

FUNCTION

(SINGLE PRESS)

“T” = H54

TARE

“C” = H43

CALIBRATION

“E” = H45

ENTER

“M” = H4D

“O” = H4F

ON/OFF

Balance
side

PC
side

Connector

9 Pins

Connector

Balance
side

PC
side

Connector

25 Pins

Connector

Summary of Contents for HPBG Series











































































Search results

Summary of Contents for HPBG Series

Reviews:

Related manuals for HPBG Series

Brands by name

Popular brands

BEL Engineering HPBG Series, User Manual

Search results

Summary of Contents for HPBG Series

Reviews:

Related manuals for HPBG Series

Brands by name

Popular brands