BEL Engineering HPBG Series User Manual Download Page 25

Page: 25 / 74

10.2 Serial output setup

Different data transmission devices and modes can be selected.

1. Select the serial output parameter as described in paragraph 10.

The currently set transmission mode will be shown on the display:

2. Now by pressing the

MENU

CAL

button it will be possible to scroll through the serial

output

MENU

forward or backward.

3. Then press the

PRINT

button to confirm the desired transmission mode.

The different transmission modes are illustrated below:

NOTE: transmission speed selection (paragraph 10.3)

4. After having selected the desired transmission mode, the screen relative to the balance

parameters menu will be displayed again. It will now be possible to select another
parameter or return to weighing mode by pressing the

ON/OFF

button

TRANSMISSION MODE

FEATURES

Continuous

Transmits the weight data in a continuous way

On demand

Transmits the weight data only when the

PRINT

button is pressed

Generic printer

The weight data is printed only when the Busy command is active

Tlp50 printer

The weight data is printed only if the Tlp50 model printer is

connected

Upon request - Glp

Transmits the weight data and the Glp information only when the

PRINT

button is pressed

Generic printer - Glp

The weight data and the Glp information are printed only when the

Busy command is active

Tlp

– Glp printer

The weight data and the Glp information are printed only if the Tlp50

model printer is connected

Continuous

Serial output

Summary of Contents for HPBG Series











































































Search results

Summary of Contents for HPBG Series

Reviews:

Related manuals for HPBG Series

Brands by name

Popular brands

BEL Engineering HPBG Series, User Manual

Search results

Summary of Contents for HPBG Series

Reviews:

Related manuals for HPBG Series

Brands by name

Popular brands