BEL Engineering HPBG Series User Manual Download Page 21

Page: 21 / 74

Setup Menù

- Weight Units

- Serial output
- Baud rate
- Auto zero
- Filter

Setup Menù

- Weight Unit
- Serial output
- Baud rate
- Auto zero
- Filter

10 Balance parameters setup menu

1. Press and hold the

MENU

button with the plate empty until the beeping stops, and then

release the button.

2. The following writing will be shown on the display:

3. Now use the CAL and MENU buttons to navigate forward or backward in the parameters

menu.

…

4. Position the cursor on the desired parameter and press the PRINT button to confirm the

selection.

5. Press the ON/OFF button to exit from the menu or select the return function and press the

PRINT button.

Setup Menu

- Stability
- Contrast Adjustment
- Backlighting
- Timer off
- Date and time

Setup Menu

- Date and time
- Language
- Calibration mode
- Calibration data
- Return

2 Sec

Summary of Contents for HPBG Series











































































Search results

Summary of Contents for HPBG Series

Reviews:

Related manuals for HPBG Series

Brands by name

Popular brands

BEL Engineering HPBG Series, User Manual

Search results

Summary of Contents for HPBG Series

Reviews:

Related manuals for HPBG Series

Brands by name

Popular brands