BEL Engineering HPBG Series User Manual Download Page 47

Page: 47 / 74

7. Carry out a tare if necessary and load the dipstick. Wait for the stability symbol to appear

and press the

PRINT

button to acquire the value. The word ‘wait…’ will appear during the

acquisition of the value.

8. The weighing of the dipstick immersed in the liquid will then be requested. Then immerse

the solid in the liquid, wait for the stability indicator to appear, and then press the

PRINT

button.

The word ‘wait…” will be displayed during the acquisition of the value.

9. The result of the density calculation of the liquid will now be displayed. If the balance is

equipped with a printer, it will be possible to print the density value by pressing the

PRINT

button.

10. The following string will be shown on the display in case of error:

11. Now press the

ON/OFF

button to exit from the density function, or the

MENU

button to

carry out the density measurement for another liquid.

Density

01-06-10 13:15:24

0.0000 g

Weight in water



-0-

Density

01-06-10 13:15:24

0.0000 g

Weight in air



-0-

Density

01-06-10 13:15:24

Dens: 1.5500 g/cm3



Density

01-06-10 13:15:24

Dens: ------ g/cm3



Summary of Contents for HPBG Series











































































Search results

Summary of Contents for HPBG Series

Reviews:

Related manuals for HPBG Series

Brands by name

Popular brands

BEL Engineering HPBG Series, User Manual

Search results

Summary of Contents for HPBG Series

Reviews:

Related manuals for HPBG Series

Brands by name

Popular brands