BEL Engineering HPBG Series User Manual Download Page 46

Page: 46 / 74

11.2.2 Liquid density determination

1. Select the density program as described in paragraph 10.

The following screen will be shown on the display:

2. Press the

MENU

button select liquid mode. Then press the

PRINT

button to confirm.

The default value of the solid’s density will be displayed. The default value is equal to
3.0000 g/cm

4. A different value can be entered by using the

CAL

and

MENU

buttons to increase and

decrease the value, while pressing the

O/T

button to pass to the next value. During the

entering phase, prolonged pressure on the

O/T

button allows you to delete the inserted

value.

5. Once the desired value has been set, press the

PRINT

button.

6. It will now ask you to weigh the dipstick in the air.

Density

Select the mode

01-06-10 13:15:24

Solid

Enter the density of the solid

Density

01-06-10 13:15:24

3.0000 g/cm3

Density

01-06-10 13:15:24

3.1000 g/cm3

Enter the density of the solid

Density

Select the mode

01-06-10 13:15:24

Liquid

Summary of Contents for HPBG Series











































































Search results

Summary of Contents for HPBG Series

Reviews:

Related manuals for HPBG Series

Brands by name

Popular brands

BEL Engineering HPBG Series, User Manual

Search results

Summary of Contents for HPBG Series

Reviews:

Related manuals for HPBG Series

Brands by name

Popular brands