BEL Engineering HPBG Series User Manual Download Page 67 | Manualshive

Page: 67 / 74

background image

66

Density:

--------------------
03-04-11 10:51:15
--------------------
d: 1.4504 g/cm3

Formulation:

--------------------
03-04-11 10:54:57
--------------------
Manual
1.      31.05 g
2.     100.02 g
3.      26.89 g
--------------------

NOTE: To transmit the print of total of weights, press and keep pressed the PRINT button

T = 157.96 g

Thresolds:

Value under threshold                      Value inside thresolds       Value over threshold
--------------------         --------------------                             --------------------
03-04-11 11:02:19                              03-04-11 11:01:50                    03-04-11 11:01:50
--------------------

-------------------- --------------------

Lim.1 :    10.00 g                                        Lim.1 :    10.00 g                                    Lim.1 :    10.00 g
Lim.2 :   100.00 g                                       Lim.2 :   100.00 g                                   Lim.2 :   100.00 g
Weight:    -0.01 g                                       Weight:      31.08 g                                Weight:     131.10 g
TEST: KO! ---                                            TEST:  OK!                                            TEST: KO! +++

Percentual weight:

--------------------
03-04-11 11:58:39
--------------------
Perc.      100.0 %
Weight:  18.69 g
Refer.:    18.69 g

Pesata animali:

--------------------
03-04-11 12:01:06
--------------------
Time = 20 Sec
M: 56.53 g

Maximum load:

--------------------
03-04-11 12:01:57
--------------------
Max.: 2.76 g

«
...
65
66
67
68
69
...
»

Summary of Contents for HPBG Series











































































Reviews:

No comments

Related manuals for HPBG Series

Brand: OHAUS Pages: 116

Brand: Tree Pages: 18

Brand: Estia Pages: 13

Brand: RADWAG Pages: 135

ADVENTURER PRO Series

Brand: U-Line Pages: 8

Brand: e-tarti Pages: 23

Brand: Digi Pages: 143

Brand: Silvercrest Pages: 40

Brand: Silvercrest Pages: 42

Brand: Silvercrest Pages: 60

Brand: OCTA-WIRELESS Pages: 80

Brand: Tronic Pages: 14

Brand: Tanita Pages: 26

i5500 iBalance Compact series

Brand: MyWeigh Pages: 4

Brand: Symmetry Pages: 15

Brand: Vigan Mammoth Pages: 28

Brand: A&D Pages: 12

Brand: OHAUS Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands