4–22
M‑3311A Instruction Book
IPScom
Setup Sequence of Events Recorder
Protective function Pickup, Trip, Dropout and/or Out-
put/Input Pickup or Dropout are selected to trigger
the Sequence of Events Recorder.
NOTE
: Communication must be established with
the target relay for this procedure. When
not connected to the relay the Save se-
lection does not save the Sequence of
Event settings to the open file.
To setup the Sequence of Events Recorder perform
the following:
1.
From the IPScom Main Screen menu
select
Relay/Sequence of Events/
Setup
. IPScom will display the Setup
Sequence of Events Recorder dialog
screen (Figure 4-14).
2.
Select the desired Inputs and Outputs,
then select
Save
. IPScom will display
a save to device confirmation (Figure
4-2).
3. Select
YES
, IPScom will return to the
Main Screen.
HMI Setup Through Fault Recorder
The Through Fault Recorder captures separate
Through Faults. Each Through Fault record contains
the serial number of the fault, duration of the event,
maximum RMS fault current magnitude for each
phase during the fault, I
2
t and the time stamp of the
fault. In addition, it will also store the total number
of through faults since last rest and total I
2
t for each
phase since lase reset (up to 256 records).
To Setup the relay Through Fault recorder perform
the following:
1.
Press the
ENTER
pushbutton.
2.
If Level Access is active, the following is
displayed:
ENTER ACCESS CODE
0
a. Input the required Access Code, then
press
ENTER
.
b. If the proper Access Code has been
entered, the HMI will return:
LEVEL #(1,2 or 3)
Access Granted!
VOLTAGE RELAY
VOLT curr freq v/hz
c. Go to step 4.
3.
If Level Access is not active, then the
following is displayed:
VOLTAGE RELAY
VOLT curr freq v/hz
4.
Press the Right arrow pushbutton until
the following is displayed:
THROUGH FAULT
ips brkr THFLT tcm
5. Press
ENTER
, the following will be dis
-
played:
THFLT CURRENT THRESHOLD
__
Amps
6.
Utilizing the Up or Down arrow push
-
button set the Through Fault Current
Threshold setting, then press
ENTER
,
the following is displayed:
THFLT CUM. I^2T LIMIT
__ kA^2-cycles
7.
Utilizing the Up or Down arrow pushbut
-
ton set the Through Fault Cumulative
i^2t Limit setting, then press
ENTER
,
the following is displayed:
THFLT PU OPERATIONS LIM.
__ Records
8.
Utilizing the Up or Down arrow pushbut
-
ton set the Through Fault PU Operations
Limit setting, then press
ENTER
, the
following is displayed:
THFLT WINDING SELECT
sum1 sum2 w1 w2 w3 w4
Summary of Contents for M?3311A
