Testing – 6
6–31
50 Instantaneous Phase Overcurrent 1-8
VOLTAGE INPUTS:
None
CURRENT INPUTS:
Configurations C1, C2, C3, C4
TEST SETTINGS:
50W1 Pickup
P
Amps
(1.0 to 100)
1 Amp CT Rating
(0.2 to 20)
Current Selection
(Sum1, Sum2, W1, W2, W3, W4)
Time Delay
D
Cycles
(1 to 8160)
Programmed Outputs
Z
OUT
(1 to 8)
Expanded I/O
(9 to 16)
Function 27
Disable
Function 46DT
Disable
Function 46IT
Disable
Function 49
Disable
Function 50W2/W3 or W4
Disable
Function 50N
Disable
Function 51
Disable
Function 51N
Disable
Function 59G
Disable
Function 87H/T
Disable
Function 87GD
Disable
1. Disable functions as shown. Refer to Section 4.4,
System Setpoints
, for procedures.
2. Confirm settings to be tested. Only the winding being tested should be enabled; the others should
be disabled.
3. Connect inputs in Configuration C1 as designated previously. Refer to Section 6.4,
Input
Configurations
, for configurations.
4.
Select W1 in Winding Config Setpoint.
NOTE:
Special attention must be taken as to which winding is being tested and which winding is disabled
when changing setpoints.
5.
Pickup Test
:
a. Press and hold the
TARGET RESET
button in, then slowly increase current input 3 (C
phase) until the selected winding target LED illuminates or the pickup indicator operates on
the computer target screen. The current level of operation will be (
P
) Amps
0.1 A (
0.02
Amp 1 A CT) or
3%.
b. Release the
TARGET RESET
button, then decrease the current. The
OUTPUT
LED will
extinguish.
c. Press
TARGET RESET
button to remove targets. This test may be repeated for each of the
other phases.
6.
Time Test
: With output contacts (
Z
) connected to the timer, apply current 5% above pickup (
P
)
Amps and start timing. The operating time will be (
D
) cycles within
2 cycles or 1%.
7.
Repeat Steps 4 and 5 for windings W2, W3 and W4 using configurations C2, C3, and C4.
8.
Winding Summing Test:
Later
9. If testing is complete, enable any functions disabled for this test. If further testing is desired, check
the proper functions to disable for the next test and continue from this configuration.
Summary of Contents for M?3311A
