Becker BE A00 Operating Manual Download

Page: 8 / 155

>>>

SAFETY INSTRUCTIONS

> D

> GB

> F

> I

> PL

• It is forbidden to exceed the supply voltages (Volts) specified for the mains adapter, the motor vehicle charging adapter

and the product. In case of non-observance, the product or the charger may be damaged, or the battery may explode.

• Do not open the product or the battery under any circumstances. No modifications of the product are permitted, any such

modification leads to the loss of the operating permission.

• Only use original BECKER accessories. This way it is ensured that all relevant provisions will be met and that health risks

and damages to the product are avoided. Dispose of the used product or the battery according to the legal regulations in
effect.

• Improper use excludes all warranties! The safety instructions are also valid for any original BECKER accessories.

• Allowed temperature range: -20 °C – 60 °C storage / 0 °C – 45 °C operation

Summary of Contents for BE A00




























































































































































Search results

Summary of Contents for BE A00

Reviews:

Related manuals for BE A00

Brands by name

Popular brands

Becker BE A00, Operating Manual

Search results

Summary of Contents for BE A00

Reviews:

Related manuals for BE A00

Brands by name

Popular brands